Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi,
I am exploring the idea of removing the JTAG port from the PCB to make it difficult to maliciously change the firmware on the field. I have the secure UART Boot-loader...
Hello
I am developing a firmware for nrf52832 using buttons like if I continuosly press my button for 6 seconds it will go to active mode from sleep mode and have been using...
Dear sir,
I have a light sensor connected to P0.04/AIN2 on 52820. How can i get the change of voltage?
I use the COMP, and has enabled COMP_ENABLED in sdk_config.h, compiled...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
We have a standalone application with no SDK integration. We would like to have the possibility to do OTA Updates via BLE and maybe introduce BLE support later on.
So for...
Hi,
I am trying to run IPSP example from nRF Connect SDK 1.4.2 IPSP sample (v1.4.2\zephyr\samples\bluetooth\ipsp). The "ping6 -I bt0 ff02::1" command is working fine but...
Hi, I am using the nRF52840 DevBoard with SDK 16.0 and Mesh SDK 4.1 and am building on the light_switch_client example.
I am trying to change the publication address by...
Hi,
I'm using nrf52 with s132(v17.0.0).
When I connect nrf52 with my phone, there is error like this picture.
And, the code is
When the buffer is filled, then...
Hello.
When I use NRF_SAADC_INPUT_AIN7 in SAADC, I get an error in calling nrf_drv_saadc_channel_init(). Looking at nrfx_saadc_channel_init() in nrfx_saadc.c, it seems to...
Hi,
In order to determine signal strength we parse the AT+CESQ response and regularly get +CESQ: 99,99,255,255,255,255 (the final number being the strength), but the connection...
Hi,
1、If I want to devlop zigbee with nRF52840, whether the only one sdk series is `nRF5_SDK_for_Thread_and_Zigbee_xxx` ?
2、Can BLE coexists with Zigbee in a nRF52840...
Hi,
I am using a nRF52832 module to receive some data from another nRF52832, which is sending the digitalized data to the receiver. My receiver consists of a nRF52832 module...
Hi guys,
I am trying to add some BLE OTA functions to my NRF52833 running Zigbee. I have looked into the examples in the SDK, and i can see that there is an example for...
