Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello, i intsalled the software stack for use with latest release of nrf sniffer package.
By starting the capture process with wireshark 3.2 i have noticed an issue:
In...
I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
SDK 16.0
nRF 52 DK
LIS3DH Axis sensor
I am trying to understand the sdk_config.h about the NRFX_TWIM_ENABLED config. Here the 'M' stands for Manager or Master? If I...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) In Product specification, it says 2...
I'm developing a USB Keyboard Receiver. But I founed that there's no APIs and no descriptions about HOW TO SEND CONSUMER KEY and NORMAL KEY in USB HID mode.
I find a lot...
hello：
I want to communicate with my nrf25U1 USB dongle. So i add some code（refer to the examples\proprietary_rf\gzll\gzp_desktop_emulator）. When i add add these files(nrf_gzp...
Hi, Everyone
I am developing with SDK 15.3.0 and nRF52832
Compiling "examples \ secure_bootloader \ pca10040_uart_debug" and "examples \ secure_bootloader \ pca10040_uart...
I can't find anything on this error on Nordic support or Segger support sites. I've looked into the obj directory and only find one main.o file (of course!). Can't see anything...
Hi. We are using a BLE module based on Nordic nRF52832 in a new product we are developing.
The nRF52832 & softdevice has its own QDID - 115277.
However the module also...
I am trying to get a project working with a main.cpp file, some C++ modules, and the 16.0.0 SDK using the IAR compiler. However, using the nrfx/mdk startup files, it never...
Hi,
Iam running the BLE uart and Zigbee light multi protocol example. Using the latest thread and Zigbee SDK v3.2.0. The example is quite good. That the door(Zigbee+BLE...
Hello.
I would like to make simple GPIO bridge. That means transmitter with Digital input and receiver with digital output. When the state of DI changes, it's transferred...
Hi everyone,
I am using nRF52 DK with 52832 on it. My current SDK version is 15.2.0. I know that for IoT applications there is external hardware needed as router like RPi...
Hi,
I have a problem with a specific Zigbee certified device that I can't connect to my Nordic device.
When trying to connect to the device, I go to see the status:
...
