Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi, I am using a system where I am using nrf52832 nordic chip. I generate a custom ble service using this ' https://github.com/bjornspockeli/custom_ble_service_example ' github...
Hello.
I would like to use the SPIS module on the nRF52840 DK. I configured it by following the examples given by Nordic.
When I use pins P0.14 (nCS), P0.15 (SCK), P0...
I am using now SDK 15.0 and the value of APP_ADV_DURATION is set to 18000 (180 sec)
But I saw that fromSDK15.2, it is recommended to change the value to 0 in order to get...
Hi,
We are running an application using REG1 only in DC/DC mode, REG0 is disabled. I believe we've found a small issue with our decoupling of all the power pins, but I'm...
Hello,
I am trying to connect my nRF9160 but am running into some trouble. Only LED 3 blinks for about 3 minutes and then just stays on without blinking; LED 4 never blinks...
Dears
I double the ble_nus_init as below ,I can get 2 service bouth have 2 characteritic.
as below:
err_code = nrf_ble_qwr_init (&m_qwr, &qwr_init); APP_ERROR_CHECK...
I am facing issue with programming of own developed nRF52810QFAA board. I used Pins 25 (clock) and 26 (data) along with Vcc and Gnd to flash device. I tried with two boards...
Hi, May I use slip library code for commercial? I have a project that uses an MCU communicates with an NRF52 BLE module. To upgrade program of BLE module, I flash the bootloader...
I’m mitgrating from nRF52832 TO nRF52810 and softdevice s132 to s112 and having compile issues.
I understand that NRF peripheral has been removed on the nRF52810 but I do...
This how i make it happend:
1.programe softdevice and bootloader.
2.generate app dfu package.
3.upgarde app via nRF Toolbox
4.It's running, all things is seem ok....
Hi, I've been working with SDK11, and now I have to move my project to SDK14 due to some issues with the old SDK. In SDK11 I could just use Keil's "Manage Run-Time Enviroments...
Hello,
I am trying to execute the SPI slave example from sdk15.2 on my NRF52832 Dev board (PCA10040 1.2.1).
I am using stm32f0 dev board as the master and transmitting...
