Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I'm using SDK 15.3, nRF52840, with the ext-flash read/write QSPI demo project.
block_dev_qspi_init(), in nrf_block_dev_qspi.c, does not uninitialize the QSPI (by calling...
Hi,
I am trying to install nRFgo Studio version 1.21.2 in my Windows 7 (64 bit OS), but half way through, installation is rolling back the installation changes and the installation...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi all,
I use ble_app_blinky example and Android nRF Blinky SDK( https://github.com/NordicSemiconductor...
During developpement of project on nRF52810, we used the nRF52DK PCA10040.
Since we wanted to use P0.9 and P0.10 (to limit differences between eval-board and real board...
I need to develop a ble advertising scanner with these requirements:
- capture at least 10 beacon advertisments (Eddystone TLM) continuously
- advertising interval of...
Hi,
I recently got the nRF51 Dongle for testing of a board with bluetooth interface. I am trying to get this dongle installed in Linux.
I found this link for the SDK...
Hi
I have a project need to be customized advertising frequency and scan in specific frequency
It means nrf52832 could broadcast at specific frequency and scanner also...
Dear Nordic Support,
I am using nRF52840 and BLE SDK v15.2. I want to control my nRF52840 through both UART CLI and BLE CLI so I try and read example: nRF5_SDK_15.2.0_9412b96...
Hello
I have a firmware with Softdevice S132 for NRF52 consists of main application (0x1F000 len:0x56000 ) and Bootloader (0x75000 len:0x9000). What I'm trying to do is...
Dear Nordic Team,
I am using a nRF52832 module purchased from Adafruit ( https://www.adafruit.com/product/3406 ) and I would like to connect it with another device with...
Hi there
First I tell you what I'm, trying to do...
I want to made a connection between a robot and a pc. Over this connection I want to program the robot with new software...
Hi,
I'm using nRF52832 SDK 14.2.0 s132 dfu, softdevice 5.0.0.
And i'm trying to update SD + BL + APP to SDK 15.3.0, softdevice 6.1.1.
When i update pakage by nRF connect...
Hi,
I am trying to upload HEX files to a nrf52832 (on a Sparkfun Breakout board) with a nRF52 DK. The problem is nRF Connect Programmer don't recognize them.
I installed...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
In sdk_config.h, BLE_ADVERTISING_ENABLED is not...
