Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi
I am using nrf52840 Dongle.
I am trying to write data to usbd using app_usbd_cdc_acm_write(usbd instace, buffer, length). But i am unable to see buffer data on virtual...
Dear ,
I am using nrf 9160 DK,
and trying to send a package of data to UART.
For example my package is: "LONGITUDEx:10.123456,LATITUDE:59.012324,UTC:20190513095612...
I am having an issue with receiving a data stream. I had started out with using the MQTT sample and experienced this issue, so I decided to strip it down to strictly a TCP...
Hallo
Im trying to get the system into DFU mode from a PC application (not the Nordic connect)
The DFU works perfectly with the Connect application and nordic tools
...
I ported an existing application(modified from SDK 15.2.0) from IAR compiler to GCC compiler in windows environment. I used the SEGGER SES for final linking using the default...
Hello,
I am using light switch example for nrf52832 development boards.I have enabled the low power node in client example.
Is it possible to configure server in normal...
The ble_gattc_write_params_t structure passed to sd_ble_gattc_write() includes a flags parameter, described as GATTC execute write flags.The only values listed for this, other...
Hello,
we plan to develop an BLE-application that needs to be as low cost as possible. One of my favourite BLE-SoCs in regard of pricing is the nRF51822-QFAB with 128kB...
Hi, I'm looking for a way to communicate with Blue tooth. I need a low footprint chip that allows for a BT HID gamepad application. I'd prefer to communicate via i2c, or some...
My application uses the nRF51822 with a GPIO configured as output and another GPIO is configured as input. Connected to the GPIO_OUT is a resistive load (Rload) which then...
Hi, we switched from your competition to your platform. I know you wrote somewhere that you cannot provide examples for every sensor out there. But your Nordic Dev Zone is...
I have run many tests using the light_switch demo. I have noticed that occasionally the latency is much larger. The latency jump is between sends, i.e. it will send 20 times...
I am using 3 mobiles for testing
1. One Plus 6
2. Samsung Galaxy Note 8 or Google Pixel
When I connect my hardware with #1 phone and send some data from the nRF Connect...
hello.
i am new to nrf52832
my question is when i press the button it will goes to interrupt handler then turn on the led if i press the same button led will turn off...
LTE link monitor does not work.
OS: Mac SEGGER IDE: v4.16 place: Tokyo in Japan.
I set up the environment from scratch following Get Started Assistant v0.9.2, updated...
