Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Take a look at a following code
void fmc_serial_rx_cb(const uint8_t* p_data, uint32_t length)
{ __LOG(LOG_SRC_APP, LOG_LEVEL_INFO,"\n-------------SERIAL RECIEVED : %s...
I am new to softdevices so please bear with me for long list of questions.
I am evaluating SDK15.2.0 examples one-by-one. I came across eddystone example (ble_app_eddystone...
Hi!
In older SDK (15.0) has been present NRF_ESB_BUGFIX_TIMER and it initialization. Now (SDK 15.2/15.3) defines this macro but not use it. Is it bug or obsolete code?
Hello Nordic Team,
I followed the tutorial as you say( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/nrf52840-dongle-programming-tutorial ). But when...
dear all,
I'm a newbie on blue tooth low energy development, I have some really basic questions that I hope someone could answer, thank you very much in advance!
what...
Hello,
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. Switch sequence followed when LED 3 and 4 starts blinking, but get the devices list...
Hi I have central device which has array of MAC address to connect.
when i see the structure of sd_ble_gap_connect() i cannot pass a uint8_t addr[5] as input.
so i tried...
SDK v11.0 & NRF51822 QFAC
I encountered a problem. In the process of pstorage processing flash data, a serial port interrupt came in, resulting in a system reset.
I used...
Hi,
I have discovered a (rare) problem where the S132 stack get stuck in connected state when it is not actually connected anymore.
This behavior was first reported by...
Hi,
SDK - nRF5_SDK_15.2.0_9412b96
HW - nRF52840 connectivity chip, other controller for application chip
We are tried to port serialization application on other than...
HW - nRF52840
SDK - nRF5_SDK_15.2.0_9412b96
We are running connectivity example in nRF52840 and connected UART with serialization application over UART which is different...
First proof-of-concept super-simple nRF51 board. When we load software onto this board, will we have to tailor or configure the software to bypass or disable any functionality...
Our application is similar to a wireless keyboard. The events are very sparse but we need low latency (~50ms). If I understood correctly, BLE is a synchronous protocol, meaning...
