Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I am trying to improve the user experience on IOS with NRF52832: I would like to be abble to scan my device and pair using the IOS bluetooth native manager.
Is there...
so far i am doing good with my nrf52840. i have played with so many examples they all work good. but the problem is when i try to merge them to full fill my need like i was...
Hi,
I'm testing the ble peripheral examples in my custom board with an nrf52810 and in the nrf52 DK (using the hardware emulation of 52810). I started with the ble_cscs...
Hi,
i am working at the moment with 2 devices using the chip nRF52832. And i have to connect these 2 chip each other with a Bluetooth connection.
i have known that this...
Hi,
I am evaluating nrf52 using the light switch example for one of our future products. I have used Nordic nrf51/52 for BLE applications in several products. This is my...
[nRF5SDK15.2.0, KeilMDK, Windows 7]
the code runs ok in the customer board, and the print log as fallows: [00:00:00.000,000] ble_scan: Adding filter on CPS_xxx name [00...
Dear nordic,
I started to integrate PCF853(RTC module) using i2c. but its not getting proper output can you help me what wrong i do?
slave address:- 0x51
read register...
Hi Sir
I enabled the "APP_UART_FLOW_CONTROL_ENABLED", but I measured the CTS / RTS pin always is low during data transmission.
Is it normal ? How to check UART FLOW control...
Hey, i have got UART work on my Thingy52 with ANA/DIG0 and ANA/DIG1 as receiver and transmitter but when I am trying to use EXT0 and EXT1 as receiver and transmitter it doesn...
Hi,
I am new to embedded device development and I am wondering if I could get some help on SPI control from nrf51422/51822 chip with dev kit to AD9837 wave generator. I...
Hi,
I am try to create a PWM output which can move the specified number of steps.
Please find following source code
After I execute above problem, I can get following...
Respected sir,
There is added external reset button at SRU532 module, and changes are given according to it using wakeup button at code.When wakeup button is used then some...
Hi all,
I am trying to implement a multilink central with UART. I had looked through the forum on all discussions in about this and followed this thread to come up with...
Hi guys,
I'm testing the 52810 duf function.
hardwar: 52810
using SDK: 15.3.0
softdevice: s112_nrf52_6.1.1_softdevice.hex
download software: nrfgo Studio
bootloader...
I am trying to flash the blink example from SDK v15 into my custom nrf52840 board, I am using pc10056 example.
I connected my ulink2 to swdio, swclck, gnd and vcc of my...
