I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
currently I am trying to figure out how to disable the cryptocell hardware after enabling it, because if I enable it and then enter systemOFF, the system still draws...
Hello,
I am using NRF52840 Preview DK, I am running peripheral/SAADC example on the board, I shorted Channel 0 and GND on the board and I am receiving negative values...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hi
Using SD Version 6.1.1 and NRF Version 15.3.0.
Using the following advertising params I can set non-extended advertising
ble_gap_adv_params_t advertisingParameters;...
Hello Nordic support, For long term power profiling of nrf52 hardware, I am using the suggestion given here, that makes use of functions in python script ppk.py: https://devzone...
Hello Nordic Team,
I have an application in development where some bigger files (~20kb) can be downloaded into the device, so they get stored in with the FDS system.
Now...
Hi,
I am using BLE application in NRF52832 board and using NRFConnect app to send custom characteristic service from mobile app to nordic device. But if I am sending a data...
I updated Thingy:52 to firmware version 2.2.0 using the Thingy:52 Android app.
WIth the Thingy:52 running v2.2.0, the WebApp for Thingy:52 can pair with Thingy:52 but it...
Hello Sirs,
We implemented a joint bandwidth test (or speed test) for a radio channel by transmitting notifications.
Parameters set in SDK config:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
I am following the instructions at infocenter.nordicsemi.com/.../nRF52840_PDK_User_Guide_v1.2.pdf to program a pre-compiled example (blinky).
I have two nRF52840-PDK (PC10056...
Hi, im designing a beacon based on nrf52832, but i have a question about RF section, i´m using 2450AT18B100E chip antenna, and to match it with the nrf52 i'm following the...
Hi,
Trying to investigate eddystone protocol. After compiling and uploading ble_app_eddystone example I see Eddystone BLE device in non-connectable mode.
But after pressing...
I am using NRF52840 DevKit on Ubuntu 18.04 (bionic). I have successfully compiled pc-ble-driver and hex connectivity/softdevice.
I have now download pc-ble-driver-py and...
