Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Dear Sir,
I wanted to connect the peripheral device to a phone which has highest rssi value(where multiple phones will be sending requests).
For that I have enabled...
in Mesh SDK v2, simple on/off model example, client node doesn't act as a provisioner.
But I still want to combine provision & client in the same device.
Is that just...
Hi all,
I'm reading the ble_peripheral samples of the SDK. I know start a advertising with the function ble_advertising_start();
Now, i know a central address, then i want...
I'm using the PPI to generate a PWM signal on my nRF51822, and I've noticed that TIMER_SHORTS is never triggered unless the timer interrupt is also active. I had originally...
Greetings,
I believe I'm seeing the same issue as this DevZone ticket: https://devzone.nordicsemi.com/f/nordic-q-a/23903/gpio-behaviour-during-power-down-nrf52832/94059#94059...
Hi dear all !
the Question is very simply,
1. What the real RESET VECTOR (isr table) , ROM address for nRF52840 MCU ? I mean what happened each time after MCU CORE reset...
Using a nRF52832-DK and nrfconnect-2.0 on Win 10 everything works well.
But using that with Ubuntu 18.04 requires more installation documentation!
1. it seems, that the...
How many GPIOTE Tasks can I use at the same time. I want to drive six different pins with six different tasks which are connected to three events. Each event generates two...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I have a peripheral (nrf52832) which is using a higher MTU (140 bytes). When I connect to it using the nRF Connect Android app, everything works. I can see the BLE_GAP_EVT_PHY_UPDATE_REQUEST...
Hi all,
I'm working with Nordic Thingy:52 (nRF6936 with nRF52832 inside).
Currently I'm working with original firmware (I mean, not modified firmware) version 2.1.0. But...
Hi,
I am debugging an SSD1306 OLED library, and in the datasheet, it does not explicitly mention support for repeated start bits. But using the nrf_drv_ API's with NRF_DRV_TWI_FLAG_TX_NO_STOP...
I would like to know what configurations are required to advertise long range.
Just changing the phy. returns error 0x07
I compared the ble_app_blinky and ble_app_att_mtu_throughput...
Hello,
I have done some consumption measurement but I have a strange behaviour while the nRF52840 is in the SYSTEM ON mode.
For the measurement, I send advertising packet...
Hi,
I have gone through the saadc example program supplied along with SDK15. But the issue is that, the example features a single channel ADC read. I tried to modify this...
