I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi,
If I have a nRF52832 project source code, how can I know it's SDK version?
When I try to open xxx.uvprojx by Keil 5.24.2, Keil reply one message "Error #544: Required...
Hello,
I have been working with Bluetooth Mesh SDK since few months. Recently, we came across a custom BLE module which has Laird's BL652(nRf52832) chip on it (Not the BL652...
Dear Sirs,
How to advertise with nRF52810 (peripheral mode) in order to be seen by BT4 devices (Smartphones)?
Is it necessary to make a special configuration (settings...
The current dimming example is able to control 1 LED.
If I want to have a different level for each LED (and there are 4 LEDs in total) then I need to:
#define ACCESS_ELEMENT_COUNT...
I want to trigger Google Assistant/Siri/Alexa on the push of a button. I found the HID code for the home button, but I presume long pressing this will not send anything to...
Hi,
I am developing one of the code for the radio testing & in which I need to pass or select the receiving channel and at same time need to receive the RSSI value of same...
Hello,
I am newbee to nrf52840, I need to start writing code for from scratch in keil and segger embedded studio. let me know the steps to get started.
B.R.
Gourav
I am using Windows 10, 64-bit
I am using gcc tools 7 2018-q2-update (arm-none-eabi-gcc (GNU Tools for Arm Embedded Processors 7-2018-q2-update) 7.3.1 20180622 (release...
I'm having some serious issues with the Windows 10 BLE drivers, it would seem that if you scan for anything over 2-3 hours the BLE just dies!
Anyway, I am now looking at...
Hi,
I have the FatFS example up and running with the SPI0 instance (default configuration).
Is it possible to use a SPIM instance instead or do they have some limitations...
Hello,
I have cloned the latest master repos and I am using the command line to build, compile, and flash. I have successfully built and compiled the new MQTT_simple example...
Hello,
Where is the nrf9160 in terms of certifications?
Is nrf9160 'pre-certified' yet in process or not planned for pre-certification? Which carriers are targeted by...
Hello,
While I tried to compile the project, I am facing error.
Preprocessor Definitions are
User Include Directories are
OS : Windows 10
SDK : nRF5_SDK_15...
In our product we offer the ability to scan for Bluetooth advertising messages, however obviously scanning continuously requires quite a large amount of power.
If we want...
I'd like to better understand 2 aspects of the Radio Test example. My apologies if this is a repost, but I wasn't able to find complete answers elsewhere in the forum.
1...
