I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I want to sync some information and control code between Nordic and our CPU(ST), so I need to study serialization function. But I only have serialization function sample code...
Hi
I'm going to use a module that uses nRF51422 and that has an adapter to be soldered as a SMD in a circuit to mimic the footprint of an AP2 module. The adapter only has...
I'm implementing my own equivalent of hci_dfu_send_hex;
There is not enough information in the documentation on how these packets are constructed.
I found that the first...
Dear community
I've got this nice "white-blue" Kit, neat toolbox to configure the tag and run it.
Now, for Battery/ImmediateAlert profiles and other parts seems to be...
Hi,
How can i test the proximity application with the use of nexus4 smart phone and nrf51822 evaluation board?
We already tested the ios proximity application which are...
Hi community,
Till now I developed some BLE applications on the TI-controller CC2540, but for my new project, it seems to bee not fast enough. So I'm seaching for an alternative...
Im mainly considerate about ANdroid and iOS devices ,I understand this is also dependent upon profile support over the android and iOS devices but this should not be an issue...
in my pca10001 board,
once i made led pin 18 and 19 pin as internal pull up.
led is not on,and i probe it also but not high.
here my config in blinky example.
...
hello
i have a problem i send from device to host the temperature, but it send the temperarture just one time
and i want that the device should send it every 10 seconds...
Hello
Im new in arduino and i want to connect an rfduino with one other rfduino
how can i send from one rfduino to other the degreee an how can i see the degree on the...
Hi!
I have a problem with testing ble_app_hrs_c. I am using nRF51822 develpment board + nRFgo Motherboard. Softdevice is S120 1.0.0 1alpha, SDK version is 5.10. Specifically...
The article that mentions the S120 and Rezence is this one: www.nordicsemi.com/.../Nordic-Semiconductor-announces-Bluetooth-Smart-solution-for-Rezence-Wireless-Charging-and...
Hello
I am new to developing with the evaluation kit and have a few very basic questions.
Any answers or pointers to relevant documents would be much appreciated.
...
I'm currently working on alert notification service. Correct me in case I misunderstand it.
having nrf51822 as peripheral with AlertNotificationServie will impose to have...
Hi,
I'd like to connect my nRF2740 to my MCU Arduino Micro and test it with the sample codes found in your GIT repo. How can I do this?
Best regards,
Alessandro
