Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
The CPU temperature module is located in the network CPU in the case of nRF5340. I have read this thread : Zephyr API to read the nRF5340 die temperature - Nordic Q&A...
Hello,
we use nrf5340 with Connect SDK v2.0.0 and we have adopted rules for indicating the update process and the operation of the bootloader in the device. Therefore, I...
I am working with the Ebyte e83 Dev board and Also got the ARM-JTAG programmer.
I have been trying to follow the nrf connect for VS code series and seems to get stuck on...
Before I got a white screen after selecting a ble chip (52840 dongle in my case), I deleted my folders home/ (.config/nrfconnect .config/nrfconnect-bluetooth-low-energy, ...
I just migrated from MacBook Air with M1 processor to MacBook Pro with M3 processor. I installed VS Code and nRF Connect SDK v2.6.0 from scratch on my MacBook Pro. hough my...
Hi，
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Greetings team,
We are using the nRF Connect for Desktop v4.4.1 and Programmer tool has been updated to v4.3.0
Using this version the MCUBOOT settings are unable to turn...
Hello, I try to config vendor id and product id according to https://docs.nordicsemi.com/bundle/ncs-2.0.2/page/nrf/ug_matter_configuring_protocol.html .
1) When I change...
Good morning,
I work with the nRF52840DK board and the BC840E and I would need to make some changes to the SW of the "radio_test" application, but trying it out I find it...
Hi,
I am going to consider NRF52811-CAAA in a design. Can you please help with these questions:
1- What is the expected End of Life for NRF52811-CAAA chip?
2- If I have...
Hello,
We have a custom board for nRF52805. We have one LED connected to the GPIO. I wrote the FW for Blink LED every second.
I build the FW using the command " west build...
Hi,
I encountered a very strange issue. We are developing the firmware using v2.6.1 SDK and using Visual Studio Code + Nordic plug.
Platform: nRF7002-DK
SDK: v2...
Hi everyone,
I am currently experimenting with the NRF7002 WiFi stack and Zephyr. I want to build a Wifi bridge from my Bluetooth mesh network. I do have some experience...
I am following the nRF Connect SDK Fundamentals and an issue with vs code at the fund_less3_exer1. Vscode doesn't seem to locate the header files of my project. It does seem...
Hi,
Is there a way to use the nRF700x 5.8 solution to access the low level PHY layer such as with the nRF58240 part number.
I would like to use this companion chip for...
