Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi, I am working with ncs v2.6.0 and I face the same issue than this post :
https://devzone.nordicsemi.com/f/nordic-q-a/98765/weird-nrf5340-behavior/420856?focus=true
...
I am using the nRF Connect SDK v2.3.0 to build applications for nRF5340 audio boards . In particular I am interested in the application : ..\nrf\applications\nrf5340_audio...
i am using nrf52840 s140 sdk ver 17.1.0 dfu/ secure bootloader/ pca10056_s140ble_debug example after flashing the code the flash memory is almost full ie 99.6% is the sdk...
when ntfx_spis_init() is done , NRFX_ERROR_INVALID_STATE errer occured.
pcb_state is NRF_DRV_STATE_INITIALIZED.
my code is
int cc3235_spi_init ( void )
{
...
Hello, Hardware : nRF5340DK SDK : v2.6.1 Context : Creating a prototype using a Load Cell and transmitting its weight on BLE. Disclaimer : I'm new to the settings subsystem...
Hello,
We are currently helping one of our client develop a product using the nRF5340.
DK versions:
nRF5340-DK
PCA10095
2.0.1
Host OS:
Ubuntu 22.04.2...
I'm a beginner to nRF52840 board, and I'm currently doing the nRF Connect SDK Fundamentals . But I failed to build the Blinky Sample due to the following error:
I'm sure...
I am working with the module nrf5340-DK. I am searching for an example to use the QSPI with the onboard external memory, could you share an example? and the other question...
Hi,
We are planning to move with the nRF5340 + nRF7002 for our upcoming project. We have some queries related to power section which are, 1. can we an use the same power...
This one is throwing me for a loop. We have a very basic NFC component in our firmware that serves up a static NDEF file and wakes the MCU from a system_off state.
We have...
Hello All,
I am programming an nrf52480 using zephyr on a windows machine.
I am trying to write a bluetooth peripheral characteristic, ore specifically to the led...
When using two nRF5340 Audio DKs as bis_transmitter and bis_receiver respectively for the iso_time_sync sample, the iso_recv event is triggered.
However, in the respective...
Hi,
I use nRF52805 chip for BLE tag. FACTOR_MODE pin will be used for production stage. At F/W start point, F/W reads FACTORY_MODE pin, if the pin is high, F/W will enter...
I am trying to program nrf5340 using this command: nrfjprog -f NRF53 --program merged_domains.hex --verify --recover -r
It works fine if readback protection is not enabled...
