Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I tried to add a chip of our own design to NCS, but when I tried to write the device description file, I ran into two problems:
1.Even if the chip description file is compiled...
Hi,
I'm using the example project usbd_msc and I am having no luck having the volume come up on windows when I plug in the nRF_USB line. I can see "nRF52 USB MSC Demo...
We are currently getting our firmware ready to test devices for FCC and other radio testing. We have an AThost-like setup that passes AT commands from a terminal over a BLE...
.Hi Nordic Support team,
I'm using NRF52832, SoftDevice S132, SDK version is nRF5_SDK_17.1.0_ddde560.
I want to transmit 9 bytes of data collected from an I2C sensor...
Hi,
the I2C burst write function below work perfectly <16 number of bytes. Once I transfer more that this, the return code throws an error "-28" and my scope doesnt even...
Hello, I would like to develop an automated tool for our production line to use to perform DFU on our nRF52832 system. Is it possible to communicate with the nRF52 Dev kit...
Hi, I developed a custom board and I am able to toggle other IO pins but somehow pin 10, 9 wasn't working. After some research, I found that NFC must be disabled to make it...
Hi,
I am trying to set EDRx en LOG_INF the result using following code:
static struct lte_lc_edrx_cfg drx_cfg ;
//enable EDRx
LOG_INF("== Setting EDRx =...
Hi,
I have a custom board with a nRF52840 and the nRF21540 FEM. To control my FEM, I have added the following to my code to my nRF52840_nRF52840.dts file:
/ {
nrf_radio_fem...
Hello Everyone. I tried to run the ble_app_multirole_lesc example on SDK 16.0.0 to test the numeric comparison match feature on bonding. And found that the handling of this...
Hello,
I am currently updating from SDK v2.3.0 to v2.5.2 but I am not able to get the 'psa' functions working correctly (as they did with previous SDKs).
I am trying to...
Hi, How to find out what function is being called, when sw interrupt occurs? I have created a timer that should call a function. But I'm having a hard time finding what function...
Hi,
I am working on custom board which has nrf9160 as modem and stm32 as host controller.
here I am used lwip stack on stm32 controller to get the IP address.
I have...
I'm trying to integrate AES-128 (ECB mode) decryption into my project
I've based it on the AES_CBC sample, and adapted it to use ECB mode instead of CBC. When I compile...
Trying to use the nRF Connect quick start with the evaluation board and the programming fails. 2024-05-22T09:09:27.145Z INFO Initialising nrfutil module: device 2024-05-22T09...