Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
The nRF5340DK's are not programmable on my pc. I have no issues using nRF52DK and nRF52840DK. I have 3 different nRF5340DK's, they all have the same issue.
When I try nrfjprog...
Hi There,
We're new to Nordic and in the process of attempting to move our custom Xamarin application and boards over to use the nRF52832 and the nRF Connect SDK. Has anyone...
Hello,
I used two samples, application_update and SLM, to test and try updating the app from application_update to SLM. I first downloaded the firmware of application_update...
I would like to store context information for each connection, but with central and peripheral connections storing different information. Ideally, this is done in two separate...
hi support team,
we can see the slide in this link: /cfs-file/__key/communityserver-discussions-components-files/4/3201.Measuring_5F00_distance_5F00_with_5F00_Nordic_5F00_Distance_5F00_Toolbox_5F00_slides...
hello Nordic
we are working with nrf52832 and nrf52840 running with ncs v2.5.0 (waiting for v2.7.0 cause 2.6.0 have some issues with cmsis fft tables that prevent us from...
Hi
We are using STM32 board as a HOST controller and NRF9160 as cellular modem. On the STM32 board PPP client is running over serial interface.
We need PPP server support...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application (in BIS mode).
I also have my own customized board, based on Raytac MDBT53v, for...
I have a nRF9160 custom board. I am using 2 UARTs (UART0 and UART2). I need to have an RX interrupt on both UARTs. I have identical setups and configuration and code. The...
We are using PC-BLE-DRIVER-JS for our central and zephyr in our peripheral (833). The central bonded with the peripheral only when the id (IRK) param in our central is set...
Hi all!
Hopefully this doesn't come off as too much of an ignorant question, but I'm having a hard time understanding the pinout of the Thingy 91 since I can't map where...
I´m trying to design a compact circuit for the NRF91, since i have limited space i´m planning to do a board stackup with the antenna board on top. Right now my board is 50mm...
I am working on an application where I am using 3 SAADC channels all with the same reference pin.
Upon startup, I will call app_sensor_init() to initialize my SAADC, timer...
Reference to my old work where I sucessfully upgraded an s140 based application to s340 (ANT supported) application here:
Now we have decided to change the bootloader...
The Commissioning and Characterization note for the nRF700x series ( https://infocenter.nordicsemi.com/pdf/nan_043.pdf ) says in section 2.1.2
However I have been unable...