Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
We try to get audio samples form analog or digital MEMS microphone to nrf54840 RAM memory with low power consumpion at 32kHz rate. We consider to use internal SAADC, PDM or...
hi, I want to use PPI function for timer trigger GPIOTE,
when timer interrupt comes, my output pin will toggle, but I find my code doesn't work, I think it is GPIOTE mistake...
I am trying to run the nrf/samples/bluetooth/peripheral_lbs example for the nRF5340-Audio-DK using nRF SDK v2.1.0. I am using the following command to run the example:
west...
We have a product on the market that uses the nRF24 and a PIC, chosen primarily for it's cost and rapid development time. We are now looking into using a nRF52 to replace...
My system details:
Ubuntu 20.04.04 LTS
Visual Studio Code 1.70.2
NCS 2.0.2
nrfutil version 5.2.0
Toolchain Manager v1.1.3
I'm trying to build my project, but...
Hi,
I'm developing my log system in a project with a secure partition with TF-M. I am following this log system design document . In my project I have, as a test, the following...
For nrf52840 which is the option for L3 Inductor. In current market L3 is obsolete. Part Number is HK100515NJ-T i need option. Also crystal capacitor part is needed.
Hi,
For asset tracker v2, it can detect the network and connect to it, and when it cannot connect to the nrf cloud, it disconnects. To be more specific, it disconnects from...
Hi Team,
I am working on connecting multiple peripherals (nrf534odk) with a central (nrf52840-dongle), some times all the peripherals are able to connect with central smoothly...
We have a separate customized build of MCUBoot for our board. This works fine. Now we would like to remove the MCUBoot build step from our app, but retain the app relocation...
Hello all,
I'm currently evaluating Bluetooth Mesh as potentiell solution for a remote control system with the option to extend the range via range extenders.
To get an...
Hello,
we need to SPI interface of a display controller RM6909 (AMOLED for smart watch) with the NRF52832 processor.
Could you please share us the source code for that...
Hi,
We are currently evaluating the Tracker V2 application.
We would like to increase GPS accuracy, before the nrf9160 returns status GNSS_EVT_DATA_READY. No problem...
hi nordic team，
i have use nrf52840 develop a product ,now i need make sig authentication to sale it .the sdk version i use is 16.0. i m sure it can pass the ble5.0 authentication...
Hey ,
Is there a way to connect and send commands directly using the dongle to the NRF52832?
If so , where can I find a protocol for the communication ?
