I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
MCU: nRF52840
IDE: Keil uVision
SDK: 15.2.0
Board: Custom
Hello,
I realize there are a ton of threads about this, but none address the specific question I have...
Hello,
My board is powered by lithium-ion batteries.
It works from 3V to 2.1V. And It stop working at 2.1V.
After discharge, I re-charged battery. But It doesn't work...
I want to achieve reproducible builds on my development machine and a gitlab CI/CD server. So far the generated binary differs if I build locally (VS Code + NRFConnect SDK...
nRF5_SDK_17.1.0_ddde560
nrf52832
Cache overflow at baud rate 921600. I use the register to complete the serial port driver. I don't know how to use registers to implement...
To the kind attention of Nordic support team,
I'm testing a freertos project, with softdevice and radio notifications. A constant number of notifications is queued before...
Hi guys. I saw a previous post saying the LE Power control not supported.
For nRF Connect SDK v2 / nRF52 or nRF53, are there updates on LE Power control?
Since that...
Hi there,
I have just started the NCS Fundamental Course and I am stuck on Exercise 4 Lesson 1 and Lesson 2. There are two problems that I am facing.
1) If I use the nrf52832DK...
Hallo,
up to now I worked with nRF52840-DK 2.0.1. After compiling, flashing the board was quite comfortable by means of the JLINK drive, which automatically opens after...
Hi there,
This topic coul be part of a BLOG POST called OTA updates of a Nordic Device I think
Btw, my issue is this: Handle an OTA update of a Nordic Device, getting...
In my project, button ,charge state check and ACC sensor Interrupt pin, use GPIOTE; when The device is charging, keep this state one night,n ot unplugging the charger.when...
Hello
I am developing a single program for two sensors, one is "BME680", and other is "BH1749" with thingy-53. But i could not see the output although i have no errors....
Hello, How to get bind state for each model (done successfully on past) with interactive py act ? When I call the command to get composition data the answer is the default...
Build the sample using west ... like so ...
west build -b nrf5340dk_nrf5340_cpuapp_ns -p=auto --force -d "C:\nRF-Projects-2\psa_crypto\" ".\zephyr\samples\tfm_integration...
Hello everyone,
I am developping a custom board with an nrf52840 chip and 2 of my boards are constantly blocked in HardFault of the cortex m4at the beginning of any program...
Hi everyone, I am searching for a solution to interface with a custom board using nRF52810 based on USB-C connector.
Our new PCB has routed the USB C data lines to nRF52810...
