Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Greetings!
We are trying to troubleshoot occasional hangup issue. We run the app in debug mode. When it hangs up, we hit pause and got the followings in the Call Stack window...
Hi,
I want to use nrf5340 dk board to debug nrf52840dongle, i have connected two board with a cable and have checked the signal is good( nrf5340 debug out p19 ------ nrf52840...
Hello all
the BLE module with the nRF52820 is programmed with a ble_app_uart_pca100e example from the nRF5SDK ver 17.1.0, according to the RSSI graph it seems it works ...
Hello Reader, I noticed two almost similar modules " DK buttons and LEDs" library and the "CAF LED & Button" library (or module). What is the difference between DK buttons...
I get the following error message from my device
àÓ FATAL: Exception occurred in Secure State [10.2 10:01:52.062]FATAL: ***** HARD FAULT ***** [10.2 10:01:52.062]FATAL:...
We have both native iOS and Android-apps that handle DFU-updates of our BLE-FW on our HW-devices. We are currently experiencing a dip in success rate (according to our firebase...
Hey Nordic,
The following are some specifications of my project.
nRF52833-DK
PCA10100
Softdevice is S122
Based on "ble_app_uart_c"
SDK 17.1.0
I am using VSCODE...
While testing a new nRF9160 based product with a Hologram SIM card, it connects fine in Minnesota, USA, but not in Winnellie NT, Australia.
Do you have insight into why...
Hi, I am using nRF connect sdk1.9.0 and modem firmware 1.3.1.
I have configured GPS to single fix mode.
err = nrf_modem_ gnss _fix_interval_set ( 0 );
err = nrf_modem_...
I have been trying for hours to get the LTE Sensor Gateway sample to work on my Thingy:91 (PCA20035) without success. According to the v2.0.2 README and the HCI low power...
Hi,
I would like to create a service that shows the current TX power of a peripheral during connection. I am using the Android nRF Connect app to connect to the nRF52833...
Hi:
I can't find the download address and description of the S110_NRF51822_7.1.0 protocol stack on your official website. I would like to know the version of BLE of this...
Hello, I encountered some issues with VS Code nRF environment. Kconfig will not open when clicked nor can I debug. When I try to debug it seems to be launching debug for a...
Hi
How can I read out the bootloader version from the main application which I defined in the zip packet (or merged hex) with nrfutil?
rfutil pkg generate --hw-version...
I'm using nRF Connect SDK v2.0.2 (in VSCode, w/ the plugin) on nRF52840-DKs.
Following the MPSL Timeslot sample , in the code shown below, I created a non-preemptible thread...
