Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello,
The following error message appears when the original code "asset_tracker_v2" under NCS 2.0 is compiled with vs code IDE,
Can anyone give me some comments? Thanks...
Hello,
I'm just trying to run the LTE_BLE_GATEWAY sample program and I've flash all the nessesary firmware onto the nrf9160dk baord. However, when I turn on the nrf52, it...
Hi,
I am building the CoAP client and sever example programs on a third party module (Reytac MDBT50Q). I am using Reytac dev board MDBT50Q-DB-40. Unfortunately the example...
Hi all
Can the NFC tag of nRF52832 be integrated with multiple cards？
Such as t he access control card of my dormitory and my home can be replaced by one card
Thanks...
I use the connected mode of DF, i use the two receiver,one transmiter,but when i flash the procedure to my boards.i find that only one receiver can get the IQ samples.how...
I am trying to port some code I wrote for Gazell, which I guess acts more elegant since it uses PPI, a workqueue, timeslots, etc. I have an ESB connection in which I receive...
Hi,
I am currently developing with the nRF52 DK (nRF52832 SoC) and the nRF52833 DK (nRf52833 SoC). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr...
HI,
I'm using nrf51822 and Gazell protocol.
from the RM, i get that the combined length of S0, LENGTH, S1, and PAYLOAD cannot exceed 255 bytes, which i think i can set the...
hello everyone, recently I entered the world of nordic,
and I have been testing some of the functionalities, of one of the devices,
specifically the nrf5304 dk model,...
Hello,
I created a device on AWS and corresponding certificates/shadows on the us-west-1 server. I'm able to successfully connect and send to this endpoint, but want to...
Hi Sir / Madam,
May i know if there is any layout guidelines that available for nRF5340-QKAA?
Appreciate if you could help to provide to ease the development of the...
My app uses mesh shell to subscribe to messages on a custom model and that works just fine
I need to subscribe to a different address on the same model but get an error...
Hello,
I using the "nRF5_SDK_17.1.0_ddde560" and want to capture the current RTC count though a gpio (low_to_high event) via PPI. I want to use the RTC2 (used by app_timer...
Hey,
We are trying to create PoC which includes NordicSemi thingy 91 or nRF9160DK, AVSystem portal and AWS cloud.
By default AVSystem uses string "urn:imei:<imei number...
