Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Dear Nordic Engineers
I use NCS 1.9.1 test Advertising Extensions,I have a problem.
I use softdevice controller,if I not set "CONFIG_BT_LL_SW_SPLIT=y",the program will...
Hi Nordic,
One of my customer is evaluate Thread for their product.
They can set up the Thread network with nRF52840DK now.
But we can't found the API of transmit...
Hi,
We are developing a custom hardware that has MDBT42 module with nRF52832 chip on it. Our project is based on the ble-throughput example and this module is using the...
Hi Support,
i did some changes(add some folder ) in gps sample program for nRF9160DK(v1.1.0) and using nRF SDK connect , toolchain 1.7.1, and getting error ( error: Aborting...
Hello
I am working on to flash my firmware binary into external flash by using nrfjprog commandline tools.
I have used below command to program and verify the external...
HI,
I am using BL653dvk board(customized ). I am following this link ( https://devzone.nordicsemi.com/f/nordic-q-a/82430/ncs-external-flash-ota-change-qspi-to-spi ) and...
Hi All,
I usually use nrf Connect for desktop in conjunction with the nrf52 Dongle (nrf52840 chip) to perform DFU's on my devices during development. but recently I have...
To get this example working, both major cellular providers here in NZ, Vodafone and Spark (M2MOne) require a specific (different) APN in order to access their networks.
...
Hi, I want to connect my PC to nRF-52840 through BLE. I git nRF connect for desktop and downloaded the BLE software to another PCA10056 and i managed to connect but i can...
Good morning,
We have a new equipment based on the nRF52840 and s140.
Just now, a new problem has appeared and it is very strange, as it seems to be a ‘random’ error:...
Hello,
I am currently using Fanstel dongle, where I am trying to trigger the USB DFU with nrf connect programmer (buttonless). The example which is provided works on the...
Hello,
I am using an nrf5340dk and I am trying to create a qdec sample using as reference the wheel module.
I have added set the CONFIG_SENSOR and CONFIG_QDEC_NRFX to...
Hello Nordic Experts,
Recently, I have been investigating the radio timing for advertising, I tried to find answers online, but I failed. To explain more clearly, let...
nrfutil is required to program the nrf52840 dongles being distributed at the 2022 Zephyr Developer Summit. west is the tool used by zephyr to install, build, flash, etc. ...
Hi,
I have a QSPI flash device with a weird bug (I think). Basically, when the RDSR command is executed, the HOLD pin needs to be held high otherwise the flash chip status...
