Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I testing asset_trcker_v2 and want to add new custom event module. I have few doubts and queries:
1. There is event_handler function in each module as well in main fuction...
Hi,
I am working on the nrf5340 with zephyr (NCS 1.7.1), I need to monitor the voltage of the battery, in the beginning, I used the ADC API of zephyr, and it works well...
Currently I have a 52840 peripheral running peer manager. We bond/peer with it using a passkey system from an mobile phone central. It works great.
SDK is 1702 nrf5.
What...
I wanted to confirm that on the nRF9160, it is acceptable to tie the VDD and VDD_GPIO pins to the same 3.3V rail and bring them up together. The VDD_GPIO rail will not be...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard
I want to add UART implementation....
Hi everyone!!! I need help with our new version of HW after validating the previous one that works.
I read some similar posts related to the GPRETREG for HOLD a GPIO while...
Hi Nordic,
We have a design where we'd like to share the 2.4 GHz antenna between WiFi and BLE.
Therefore, we need to power and configure the RF switch accordingly, before...
Hi,
currently I am using nRF52811 in one product with BLE functionality. Now I would like to use the same MCU in other product where BLE is not needed. In this case I would...
We are developing a product based on nRF52832 and we need to verify that in case of problems, the device will "fail gracefully". So we looked at implementing the ARM handlers...
I am using LSM6DSOX IMU sensor INT detection with NRF52-DK and have extra 400µA (PPK2 used) on my setup. After a few days of nightmares I finally found that this is related...
Hi,
I'm using nRF Connect SDK v1.9.0
We're working on firmware running on an nRF9160 with TF-M enabled. We need to link with a library to is built with hard-float, so...
Hi,
i want to read temperature sensor value inside the nrf soc on bl653 board. while checking there is a file inside ( \zephyr\drivers\sensor\nrf5) this path. how to configure...
Hi,
I am working on DFU-OTA example. am looking for example , which will help me to copy image from slot1 to slot0 without using scratch pad. it has to override the image...
Hello Team,
I am using the ble_app_hrs_rscs_relay example where NRF52 acts both as a central and peripheral. My question is that when I remove the heart sensor Polar H10...
