I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello,
I'm a beginner of nrf5340, when I tried hci_pwr_ctrl(ncs v1.5.1) , I met some problems.I adjusted the tx power and changed prj.conf :
Then I added hci_rpmsg...
After updating nRF Connect and the Programmer app, DKs aren't being recognized when clicking on Select Device.
Tried both with nRF9160 and nRF5340 DKs and neither was detected...
I'm working with the PCA10040, the SDK V11.0.0. and the winbond memory flash W25Q80BV.
For the SPI connection I'm using the the SPI2 because TWI0 and TWI1 are being used...
Hello
First of all, I`ve been spending way to many hours trying to figure this out, so I decided to open this ticket. I am new to microcontrollers in general and the Nordic...
Hello:
I'm new on nrF52832 development. I did some tests using nRF51 and so far so good. However I received a few samples of E104-BT5032 from eByte http://ebyte.com/product...
Hi,
I have 2 SES projects that both require softdevice plus application.
One of the projects combines application and softdevice into the .hex file that is generated...
HI
I am Programming in Keil IDE and I am using ST link v2 like debugger, but in Keil shows this problem "internal command error"
what is the problem? I was thinking...
I'm trying to build support for uart async api by adding:
CONFIG_SERIAL =y
CONFIG_UART_ASYNC_API =y
to my prj.conf. Without CONFIG_UART_ASYNC_API the app compiles...
The nRF Connect Extension for Visual Studio Code was recently updated to v2021.10.103 but, unfortunately, a problem mentioned in this post still exists: "Unknown board" issues...
Hi,
In the documentation for the nPM1100, in the section " Charging indication (CHG) and charging error indication (ERR) ", there is a schematic for connecting ERR/CHG...
HI.
is my first time to using Nordic devices, and I'm going to program nRF52840 to medical product,(oximeter, gyroscope, etc.), I am using a dev, module basic, only to test...
Hi By mistake I closed below but the issue not resolved yet.
https://devzone.nordicsemi.com/f/nordic-q-a/81276/agps-example-question-related-to-psm-command-disablement ...
I want to set an external LED on and off with the coap server example, but It doesn't work. I tried two different methods. The uncommented one is more like a normal blinky...
Hello,guys
I build nrf9160-dk modem_shell demo as cmd '$ west build -b nrf9160dk_nrf9160ns ' and then '$ west flash ', after the system running up, I try to ping baidu website...
Hi,
I have a question about the TID field in Generic OnOff set message. I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. I have enabled...
