Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi All,
Sanity check here. I'm reading the RSSI value from a received packet
if (nrf_esb_read_rx_payload(&rx_payload) == NRF_SUCCESS) { if (rx_payload.length > 0) {...
A device that is provisioned with PB-GATT enabled stops receiving mesh packets after the provision is complete.
When the provisioning process is complete nrf_mesh_disable...
HI,
I got the following log while advertising:
SOFTDEVICE ASSERTION FAILED AT 0x00014AA6
Since this address locates at softdevice, I can not know what happens.
Would...
Hello,
Using nRF52 DK boards, I'm trying the simple_message_model by modifying the light switch example.
With the client, I simple send a 12 bytes unreliable message by...
Hello! I have a question about nordic thingy 52. Is there any possibility to play more than 8kHz on this board? For example: if i will change speaker on another it could help...
Hello, How do I set the analog reference voltage to external pin P0.02? I'm using the arduino environment so I don't know how to set it via those registers? I'm currently...
Hi,
I am using SDK 15.0 on a custom board using nRF52840. Softdevice is 6.0.0. Coding with SES.
I am investigating and trying to fix the infamous IOS caching of characteristics...
In the schematic of the nRF52840-DK L1 and C4 form the matching network. C22 is noted with NP, but on the DK i have, is a component placed.
Since i would like to use the...
Hi to everyone!
I've been testing the Bluetooth on the nRF52832 DK board with some of the examples and I have saved the mac address (obtained from my smartphone).
In...
Hello All,
I was wondering if someone can confirm the consumption of the nRF52840 in SYSTEM ON when running the Power Management Example on the nRF52840 DK board (in nRF...
My end object is to connect the peripheral to one required central. It should not get connect to another central or to the nRF connect app.
I have gone through many example...
Hi everyone ,
I'm looking for the ULPMark score for the nRF52840.
On the EEMBC website, I 'm seeing that Nordic Semiconductor is a partner, but I don't find any information...
Hi,
we are late stage development on NRF52840 with sdk 15.0 and softdevice 6.0. The mind turns to certification. It all seems very complex and confusing
1) Do we need...
I have an nRF52840 based peripheral running SDK 15.3.
I have a custom service with a write characteristic and a read characteristic. The peripheral supports multiple connections...
As far as I can tell the values are inverted.
4.8.2.2.1.1 Occupancy Attribute
The Occupancy attribute is a bitmap.
Bit 0 specifies the sensed occupancy as follow:...
