Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi, I am working on a project in which the device (nrf52832) needs to be both central and peripheral and it can transmit/receive some commands through UART to set the advertisement...
Hi ,
We are using the BL652 module with your nRF52832 chipset in our important product.
In our product the wireless connection is fundamental and we would like to test...
Hi,
I am using nrf52832 to achieve system-off with low power consumption. Nrf52832 and a rf IC communicate via SPI.
I configured a pin as the wake pin.
nrf_gpio_cfg_sense_input...
Hi, I am trying to use github.com/.../nrf52-ble-image-transfer-demo with Ubuntu 16.04 Using - gcc-arm-none-eabi-6-2017-q2-update - nRF5 SDK version 15.0.0 (nRF5 SDK version...
I use SDK 15.3.0 with the example of USB_CDC. In the example, the virtual com port transmission works only when the terminal sends a DTR signal. I need the DTR notification...
Hi
I am trying to implement DFU to my project. I have done all the steps to generate packages, private and public keys etc. My program now starts at dfu and I can upload...
Hi,
setup: nrf52840 dk, no battery installed (power comes from USB connectors), switches are in default mode (SW9: VDD, SW6: default).
Flashed open_bootloader (dfu/open_bootloader...
Hello,
I'm using S112 V6.1.1 with the Nrf52810. I get a error using sd_ble_gap_adv_set_configure() after a connection. On BLE_GAP_EVT_DISCONNECTED i try to change the advertising...
After testing the nRF9160-DK with all available samples, we decided to integrate the nRF9160 in an own new product and have now a prototype available. And of course some questions...
Hi,
I am using Mac OS and 15.2.0 SDK on nRF52832. I was trying to do BLE DFU following this link . When I was trying to push the DFU zip file, It was resulting in the following...
In following the instructions of the nRF_Sniffer_User_Guide_v2.0.pdf, I'm attempting to use Segger's J-Link software to configure my nRF-51822. The environment is a Mac OSX...
I bought the nRF9160 dev kit and I can't connect to the j-link: JLinkExe SEGGER J-Link Commander V6.30f (Compiled Mar 2 2018 17:30:55) DLL version V6.30f, compiled Mar 2 2018...
Hi ,
In the target hardware I am able to detect the Nordic chipset nRF52480 by flashing USBD application on the chipset using JLINK SWD.
Now I have query related how I...
