Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
I am working on an older project that was developed using SDK 11.0.0, SD S132 2.0.1, and "Eclipse 2018-9." No MDK appears to be being used.
I understand that the MDKs are...
Hello,
BLE 5 applications on the nRF52810 which softdevice should we be using S112 / S132 what are the primary differences between these? I wanted to know a comparison...
Hi,
I'm collecting data from BLE and storing them into nRF52840 Dongle by using nrf_fstorage_write procedure. Everything works fine so I can write data into flash by nrf_fstorage_write...
When I run the TWI scanner example, an unknown address shows up in tandem with my TWI device address.
I am connecting a MAX30101 EV kit daughter board to the nRF52840...
In the secure DFU bootloader, I have some custom initialization that I need to happen after the BLE transport is initialized in nrf_dfu_init(), but before loop_forever() in...
Hello everyone,
I've got an issue with ESB. I'm using 3 nRFs 52840 with firmware based on SDK 15.2. One of them, the radio-receiver is RX, and two of them, PilotA and...
Hi,
I'm working on putting our system into low power idle mode. We use MyNewt to build our application. In order to get to the lowest power, I disabled BLE and all our drivers...
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm trying to get the code below to compile. One question is how to fill in the nrf_crypto_hash_info_t structure. Another issue is that the nrf crypto includes don't compile...
Chip: nrf52840
Platform: Android
MacOS Dev
There is pretty much no error logs but it can't actually send anything over mesh network on udp. Seems to receive without...
I have a RedBear BLE Nano v2 (nrf52832) connected to 3 AA batteries for power. I also have a Maxbotix (MB1043) ultrasonic sensor attached. I have configured a gpio pin for...
Hi, I am a beginner to nrf24le1. My company has products made of nef24le1. I would like to debug nrf24le1 devices but couldnt able to , I would like to know the answers for...
Hi. I am trying to run the makefile of ble_app_blinky (from SDK 15.2.0) on Ubuntu 18.04 and Visual Studio Code. When running "make" in the armgcc directory, the following...
i have recently upgraded to SDK 15.2, and since doing so I am struggling to get timestamps working in the logger.
I am initialising the logger here:
And here is my microsecond...
Hi all,
I've just downloaded SDK 15.2.0 on Windows 10 and it was unable to unzip the file and reported an error. I copied the file to Mac OS and got the same error.
Is...
