Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
When I go through the code of light switch example, I am confused about relay functionality.
Compare with the v2.1.1, I can find the m_relay_enable in network.c but...
Hello!
We are currently developing a software solution which integrates many protocols into one Gateway. One of the protocols is Zigbee, and since it is the first time we...
I'm running FreeRTOS with SDK version 15.0 on nrf52 custom board.
I have two sensors, say A and B, on two separate SPIM bus instances. Sensor B utilizes PPI to trigger data...
I've been working on using an nRF52 as a host for a PS/2 synaptics touchpad mouse (to integrate with BLE HID). I was able to get a correct mouse position using two GPIO pins...
Hi,
i am using oled ssd1306 i2c with nrf51822. I am using peripheral mode and SDK v10.0. i choose this sdk version because of length i want to sent at one go that is 1024...
Help pls, i can't build a project.
Building ‘temp1’ from solution ‘temp1’ in configuration ‘Debug’ 1> Generating linker script ‘temp1.ld’ 1> Linking temp1.elf 1> Output...
Hi,
It seems that I have an issue with ZB_GET_OUT_BUF following the zb_zdo_node_desc_req example.
After several calls (around 10) of ProcessNodeDescReq , I can't get a...
I am using Linux (various breeds and hardware) and the nRF52840 Dongle. When I first plugged the dongle in it worked as expected
Then this
this is the output from dmesg...
I am reading up some open source bluetooth stack implementation with NRF51822 with the objective to understanding the Bluetooth firmware.
My prior knowledge are baseband...
Hi,
I'm working on this module. ( https://fccid.io/2ALGYNRF52832AA/User-Manual/15-NRF52832AA-UserMan-r1-3763863 ) This module has 1 cyristal bu nrf52 dk has 2 cyristal...
Hi guys,
i would wan't to implement support for 1MBPS (mobile phones without extended) and CODED (long range which uses extended) at the same time.
One idea is to use...
Bear with me, this might be complicated. I'm currently transmitting some audio data via ESB. The data gets passed as followed:
Microphone (PDM) -> nRF52 (1) (SPIM) -> nRF52...
I am creating an iOS which needs to talk with nRF51822 Soft devices 100.
Problem i am facing is, I am not able to Encrypt the connection properly.
I am using
- security...
I have created three nodes(A, B, C) one client(i.e A) and two servers (i.e B and C) using simple_message_model. The node that contains the client model(A node) provision the...
Hello,
I'm having a weird issue that I don't really understand.
I am currently replacing an old timer-based time-keeping implementation for a new RTC-based implementation...
