Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
Hi,
I am using pca10040 board of nrf52 dk. I am running battery level measurement code on board but whenever I observed values on serial monitor it shows garbage values...
Dear Developers and Members of the Forum
I have an Apple Macbook 6.1 (Late 2009) that has a built in Bluetooth Chip (Broadcom 2.1+EDR) and I want to use Xiaomi Mi Portable...
Hi,
I am trying to develop low power beacon on nrf52.
Which example should I base on?
I am trying example ble_app_blinky on PCA10040, and I am getting close to 1 mA...
Hi,
I have implemented the Master serial DFU code to update application and SD file. I'm following DFU packet send sequence. Ping, inti packet, FW packet.
I'm framing...
Hi,
I need to develop code for the custom board test, in which I need to enter the <channel> and it <power> value & then begin start/stop the continuous transmit the radio...
Hello,
Recently I purchased a nrf52840 Dongle to use it with nrfConnect for Windows.
I use nrfConnect 2.6.1. When I insert my Dongle in a USB port the LED starts pulsating...
Dear Sir,
We need a sample code for UARTE nRF52832 using EasyDMA. This sample code should drive our UARTE port using in BLE to UART mode. We could not find it by asking...
Hello, i am working with the nRF5 Mesh SDK on nRF52 based boards. Starting from the light_switch example i created a custom model to perform light control and other tasks;...
I cannot set the location in my Profile, this is required for private tickets. When I type anything, I get a window with pulsing elipses, and nothing pops up. I've tried my...
Hi,
I have used "ble_app_gl" example for pairing with random key and it runs great. Now i want to add push button for pairing purpose which is like..... when user enter...
Hi,
I am trying to understand Wireshark logs when sniffing packets. Please check the attachment. I have been reading about the description of advertising packets. Can you...
Product: 4 peripherals and 3 client connections
I am using 2 separate flash areas/records.
The PM starts at 0xF8000.
Product flash starts at 0xfA000 and is 3400 to...
I'm using nRF51822 IC rev2 and testing DFU example.
To create firmware package, nrf.exe is required.
This tool is automatically installed with Master Control panel.
...
