Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hello, I recently installed nrf sdk but I have trouble getting through getting started phase. I'm using ubuntu 24.04 and created workspace environment using CLI. Below is...
Hi I'm encountering an error while building Lesson 8, Exercise 1, Step 3 using the nrf7002dk/nrf5340/cpuapp target board. Below is the error message I received:
The same...
Hi, I have a BLE device in Observer role - it will constantly scan for Broadcasters broadcasting our unique UUID and put these scanned devices into a Ring Buffer.
The reason...
Hello,
I've encountered a condition where k_sleep(K_SECONDS(1)) never returns. Here is minimal example, reproduces both on nrf9160 and nrf9161:
Hangs up after printing...
Hi!
I am looking for a NRF52840+OpenThread+Azure IoT Hub SDK solution. Here is what I did so far. Nothing helped:
Thead CLI Example on NRF52840 + Border Router on...
Hello Nordic Team, We are currently using nRF52833-QDAA SoC for developing a new project that incorporates geofencing functionality using BLE.We . We tried using the example...
WE are working on nRF52832 and nRF5 SDK 15.0.0. Currently working on the BLE FOTA process and have successfully completed DFU up to this point. Our next goal is to save configuration...
Hi,
I just finished to setup everything to start using nRF Connect for VSCode Extension. I followed the "nRF Connect SDK Fundamentals" course in the DevAcademy.
I installed...
Hi,
nRF5 SDK for Thread and Zigbee supports DFU OTA over Thread, but I can't find the corresponding function in NCS.
If I want to implement DFU OTA over Thread in NCS...
Hi Team,
I'm analyzing to use nPM1300 PMIC in one of my projects. I planned to use the integrated Buck to power my on-board device. But, the calculated current consumption...
Hi Nordic team, I am facing an issue about using simple gpio to control external FEM( custom FEM model ) in NCS 2.7.0 & nrf5340. Here is background: 1. Our project is using...
On NRF52840, programming provision.hex with the command as follow:
%nrfjprog -f nrf52 --sectorerase --program provision.hex --reset --verify
On NRF54l15, the nrfutil...
Test platform: nRF54L15-DK
NRF Connect 2.9.0
When calling spi_write_dt, under the hood spi_nrfx_spim.c > configure is called to prepare the SPIM interface for a transmission...
I have an application that runs well on nRF52DK. It is like peripheral uart. I only use Tx/Rx and one LED. With OTA. All works as intended. I use NVS for parameters but nothing...
I've been trying to enable the watchdog as early as possible during boot. I haven't been able to find any way to configure the nrf52832 watchdog to enable itself prior to...
