Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello,
In a project using the NRF52832. Softdevice SDK 19.1.0 and Segger IDE, I inizialize the BLE for having NUS and DFU services actives. I try to reproduce the code here...
Hi,
I would like to ask when using zephyr's k_timer it uses a clock from LFCLK, then it can be generated in the following three ways:
32.768 kHz RC oscillator (LFRC) 32...
Hello Team NordicSemi Q&A,
I am beginer in Nordic Semiconductor Device. My question is related of nPM1300 Quiescent Current. In datasheet for Sleep Mode and Hibernate Mode...
Hi. i am trying to turn ON a LED1 and read its status and then turn ON LED2 based on status of LED1 in nrf52840dk board.
#define led1 28 #define led2 25 #define Button 12...
These seems like another dumb question. First off, I am aware that the nrf21540DK is the nrf52840 with the FEM tacked on the output.
I know I can select the nrf21530DK/nrf52840...
Hi,
I’m experimenting with the nrf9160 LTE modem in poor network conditions. I would like to be able to keep track of how long the modem spends searching for LTE networks...
Hello,
I'm having an issue with performing fw update with ble mesh DFU examples.
My setup is pca10056 used as distributor and pca10059 - dongle as target.
I'm using...
Dear,
My customer interesting in nRF52840-DK and would like to know the U2 (IC).
Customer wants the nRF52840-DK board it must be installed IC in the same package (QFP...
NRF_CLOCK->TASKS_HFCLKSTART = 1; while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0); NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
I finally figured out the problem with my custom board...
Hi,
I am using nrf52840 to run as an hci controller over UART for nrf91. I was able to implement FOTA over BLE for nrf91, but I would also like to add an option to add FOTA...
Hello,
I'm trying to configure the GPIO pins on the MDBT42Q-P192KV2 module, but they are not responding as expected.
I'm using the nRF52840 Development Kit to flash the...
Hi,
The errors that need to be resolved are as follows, and I think the sdk is not installed properly:
1.Please help me troubleshoot the installation problem of nRF...
nrf5340_audio application ， unicast_audio and broadcast_audio samples in zephyr， Are these all LE_2M by default ?
If I want to use LE_1M, how to change ? Modify prj.conf...
Action for Loading configuration is bugged. It Exports .overlay file but when Loading it only accepts .json file and it doesn't allow you to change it. Therefore, the file...
