Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I am currently working on communicating between the nRF5340 DK and the nRF5340 Audio DK over BLE. Could you please share the information flow?
Warm regards, Rajendra...
Hi,
We have modified the throughput example of NRF5340, v2.6.1 SDK to achieve around 600 Kbps for iOS app. Attached is the sniffer trace.
Can anyone confirm that the data...
I'm seeing duplicate data packets while analyzing our sniffer trace from NRF5340 to iOS app. However, there is no packet loss or any impact on data rate.
What might be the...
Board: nrf5340dk (build board: nrf5340dk_nrf5340_cpuapp) / SDK: v0.16.8 / I'm a complete beginner who touches the nrf board for the first time My Project: max30101 --(measured...
Hello
we have some own created UART drivers which access the UART registers directly.
Those drivers have been working withe the older chip revisions for years.
Currently...
Hi,
I cannot resolve the problem while setting up modem trace RTT logging. I'm also unable to find up-to-date information on how to set this up.
I have connected DK as...
I'm close but this is not working for me yet. I'm trying to send a few hundred bytes from android to my nrf device. So I tried to implement long write where you set prepare...
Hi I've a side request, into the exercise I've to perform some changing into the DK programming interface through the JLink, so the question is how to restore the predefinite...
I am getting an fs_close() -5 error (-EIO) when I write to an SD card using fatfs. I determined this error was associated with FR_DISK_ERR in fat_fs.c.
Additional info ...
Hi,nordic team，
im use nrf52840 develop my product with sdk ncs 2.6.the speed of desktop dfu is so slow,and the speed of configurator channel is also slow.i want to transfer...
Hello. I am facing an issue in configuring ADC for multichannels. I was looking at the Nordic fundamentals course Lesson 6 Exercise 2 .In this example, the adc is configured...
I was working through Nordic Intermediate course lesson 8 exercise 2 - DFU over USB, adding external flash and custom keys. I was using an nRF5280DK. (Sticker: PCA10056 2...
I have been trying to implement a DFU OTA using Bluetooth Low Energy from one nRF52840 DK to another nRF52840 DK using the smp_client_ble ( https://github.com/hellesvik-nordic...
hello.
I am using nRF52820 and nRF5 SDK (17.1.0).
When the fds_gc() function is executed, all bonding information in the pairing area (flash) is erased.
My understanding...
