Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Setup:
- nrf-sdk (v2.7.0rc2)
- custom board with nRF52840 QIAAD0 SoC
- current measurement directly on nRF VDD using Keysight 34465A, VDD=1V8
I'm using a code which...
Hello,
So I'm trying to setup the driver files and default configurations for CS47L63 Hardware Codec. There are no build errors or flash errors but after flashing I get...
I have a custom board with a nRF52840 and a nRF21540. To control my FEM (nRF21540) I have added the following to my code to my nRF52840_nRF52840.dts file:
/ {
nrf_radio_fem...
I am trying to control the 485 relay using the 485 to ttl converter. I implemented it on arduino using the following code:
#include <SoftwareSerial.h>
#define SoftSerial_RX...
Hello,
I am using bis gateway on nrf5340 audio dk to transmit data.
In addition to audio encoded data, I also wanted to send some additional data, so I put these data...
We are experiencing intermittent connection issues with the nRF9160 using NB-IoT on the Vodafone UK network. Our devices fail to connect or register with certain cell towers...
i have changed light example demo server.
now i add #define MESH_FEATURE_RELAY_ENABLED (1) in nrf_mesh_config_app.h ，the server have supplyed friend feature， i used nrf...
Hello, I'm trying to implement timer-driven ADC acquisition with the nrfx library. I previously configured some timer-drive GPIOs like in the following code
I'm having...
Dear DevZone Team,
I'm facing a very strange issue whereby the sample code from the Lesson2_Exercise2 of the Wifi Fundamentals course does not allow my development kit...
I currently use 8 nRF52832 as PTX and 1 nRF52832 as PRX. To ensure better communication quality, I wrote the code for PIPE allocation. The channel is assigned by PIPE 0 as...
Hi,
I'm working on a custom board with an nRF52840 MCU and a MAX17260 fuel gauge IC interfaced via I2C. The goal is to read the voltage of a battery using the MAX17260....
Dear all.
I have one question about thread certification environment:
I want to setup internal test environment only with Nordic nRF52840(no other bed devices). In the...
Hello,
In an existing device using the nRF52832 I have 2 SPI Master instances. Please, may you confirm that is possible to create a third SPI Master instance?
By the way...
