Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
I have setup the UART along the same lines as the sample project in the DevZone Academy. I have extended the example provided to suit the project needs.
What I am getting...
Hi all, We have a custom board running with a project based with ncs v2.6.0. On our board we have two external flash, one is used for DFU the mcuboot_secondary with QSPI and...
Hello All,
I am not able to find the nrf_drv_adc related files in SDK folder. ADC library is not supported in NRF5_SDK_17.0.2 is it so?
Thanks and regards,
Neeraj...
Hi Team,
We are testing the nRF7000's Wi-Fi location feature to enhance our device's capabilities.
Our setup includes:
nRF52832 as a BLE beacon
nRF9160 as a host...
When I follow exercise steps A to open nRF connect terminal,vs code will display issue as follow:
Whether some issues happened when I get nrf connect SDK?
How can I...
Hi community,
It's my first time building a board with a Nordic chip so for sure I've made a lot of mistakes. I made this with KiCad and uploaded all the files to the repository...
What is the possible reason that LED1 blinks and LED2 does not light up when the nRF5340 Audio source is operating?
I have read and understood the source code, but I am...
We've added our app's overlay files into the mcuboot child_image directory so that mcuboot is initialized with the proper state of the board. In our nrf5340_cpuapp_common...
Hello,
Using wifi monitor sample on NRF7002 DK, packet length is constantly 70. It was checked both by reading received variable from:
received = recv ( packet -> recv_sock...
Hi Nordic DevZone Community,
I am working on a project using the Zephyr RTOS with an nRF52833 series board, and I am trying to interface with an SSD1306 OLED display via...
I have a device with a programmable output pulse width for its data ready signal. I need to be able to reliable receive the pulse so I don't miss any interrupts, and I'd like...
Hi everyone,
We are using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. Our application collects data from a sensor via I2C and then sends this data to a smartphone via...
Hello,
We are doing some Wi-Fi connection tests on our custom board equipped with the nRF5340 and nRF7002 chips, and at some point during our tests, we encountered a strange...
Hello,
I found the GPIO P0 menu in the peripherals view:
Tried to change the value with the tool (set to output) and manually (changing the register value from 00A00000...
