Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
What is the correct way to build an application (say asset_tracker_v2) included in a newer SDK (2.6.1 for example), using a nRF9160 DK without on-board SPI flash device...
Hi,
I have a bunch of openthread routers and TTM shows one as in some error state.
RLOC is 0x9400, but no ext address is shown.
Also a child connected to this router...
Hi everyone,
I am planning to use the cadence/publish interval property within a mesh network. I can not find any examples on how to use it. I know I can set it in the nrf...
I'm developing a BTLE sniffer app to run on a headless raspberry pi 4 with html/php/js access. The application runs well on the development platform - Ubuntu 22.04.
On the...
We have some custom hardware that utilises an NRF52832. Up until recently, all our firmware was built on NCS V2.2.0, which I believe used Zephyr V3.2.99. We have implemented...
Hi,
I am moving to version 2.6.0 of the SDK and toolchain. I am developing on windows 11 pro. Our cMakeLists.txt file creates a version file in our conf directory version...
Hello,
We have a custom board using a nRF5340.
We followed this course implementation for simple serial recovery over UART (and also tried CDC ACM) but as soon as activate...
Hi, I am trying to download all software necessary to program nRF chips. I am following this academic course Lesson1 When i try to install nRF connect SDK after toolchain...
We would like to develop for the waveshare 1.02 e-paper display. We have limited experience with SPI on Zephyr and are looking for the easiest way to get a "hello world" result...
Hi everyone!!
Im very new to this firmware space and would love some help.
Currently I have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
Hi everyone,
I have a fairly mature project that I am now required to add MCUboot to so that remote firmware updates can be possible. I am building for a custom board based...
Hello,
I use a RF52-DK board for flashing/debug Nordic microcontroller. When I connect the board on my mac, the "JLINK" volume is mounted/ unmounted every 2 seconds and...
Hi,
I tried the radio_test sample with the sdk 2.3.0 on a custom board. I added this to the prj.conf
And this to the app.overlay
With this I had a ttyACM0 and...
I have used ncs-example application workspace to develop our project. In that we were trying to include WIFI, so we include all (sample/wifi/sta) content to my project. but...
