Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I have a proyect with the following memory requirements.
The current project has a propietary bootloader and bare-metal application. Therefore there is no Zephyr...
Hallo,
In the BSP startup files for the nRF5340 (gcc_startup_nrf5340_application.S & gcc_startup_nrf5340_network.S) the interrupt vectors USPTn_IRQHandler (n=0,...,3) are...
I hope someone can help me here with my question.
In my project we are using a nrf9160 with modem fw version 1.3.5. The application sends/receives data periodically (1 hour...
Hello and thanks for reading.
I have a critical problem with my device, and seeing as the problem is BLE related I figured I would ask your help as well. We are using the...
I'm using an nRF9160-DK board with the provided iBASIS SIM card. I followed the instructions here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.4.0/nrf/working_with_nrf...
Hi, I have a problem related to DFU OTA through BLE
When performing OTA through Bluetooth, I encountered the following issue:
Firmware built in the same build can be successfully...
Hello, I started looking into the DPPI from NRF5340 series and planning to integrate some functionality into an existing zephyr-based project. Specifically, I need timer-based...
Hey team,
We're having trouble with our device. It's been working fine, sending messages to our backend without a hitch. But after a while, it starts having problems connecting...
Hello.
The MCU of our new design will be the nRF52832.
I would like to know if it is ok to read the voltage of the battery that powers the system, nominal voltage of 3...
Dear support team,
1. Can mesh provisioner configure multiple devices at one time? For example, there are five unprovisioned devices within the provisioner's network. Can...
Hello,
I cannot flash the nRF52840 Dongle using Programmer 4.3.0 with hex file sniffer_nrf52840dk_nrf52840_4.1.1.hex.
The option for writing is grayed out. =
- python...
While developing, I usually connect to the Serial COM Port to see my print statements.
However, when the devices crashes, only "*** Booting nRF Connect SDK v2.5.1 ***" is...
I've got a project that I'm going to want to do DFU through the UART, and in order to transfer files in a follow-on activity, I want SMP running in the application. Therefore...
We're trying to connect to our Azure Iot Hub using the Azure Iot Hub library provided by Nrf Connect Sdk 2.6.0 (without DPS). We're currently using the evaluation board to...
Hi,
I went through the Nordic Academy nRF Connect SDK Fundamentals - Serial Communication. I tried the exercise program where LED1, LED2 and LED 3 are toggled by pressing...
