Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi, I'm working with just one NRF5340 audio DK and I saw this ticket where it was commented that it is possible to reduce the use of 2 NRF5340 audio DK's to just 1 using a...
Hi,
I have one central and one peripheral devices running. Currently I run a scanning filter on Central side and connected to the peripheral with desired name.
But now...
I was trying to follow the instructions at https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf52_gs.html#connecting-to-the-application for testing my nrf52840...
Hi,
Using Windows 10 and SES
SEGGER Embedded Studio for ARM Release 6.34a Build 2022083102.51023 Windows x64 2014-2022 SEGGER Microcontroller GmbH 1997-2022 Rowley Associates...
Hi all,
I want to ON and OFF advertise manually
My code working steps
1) (APP_ADV_DURATION 3000 ) after this seconds over
2) It hits on_adv_evt() function in this...
Hi All,
I am using asset_tracker example V1.8.0, it's working fine with nrf9160DK. I am able to see the data on nrf cloud.
The purpose of testing this board was to debug...
I am working on two devices, a peripheral and a central. The peripheral is custom hardware. The central is being run on a Rigado BMD-300 series evaluation kit. I'm using Segger...
Hi,
Perhaps this question is too basic, but I haven't been able to find this anywhere.
I've followed this tutorial successfully with an nRF52832 DK:
However, I'm missing...
Hello,
I wanted to create an SPI shell, similar to what is available for I²C. I am therefore trying to create a generic SPI device in the devicetree:
Somehow I am...
Hello,
We use nRF52840(0dBm)+nRF21540(Dec6).
In the case of using nRF52840+nRF21540, tx spurious emissions occurs severely in the nRF21540 output.
FEM(nRF21540) output...
Hi.
I am developing a custom board using the NRF52840. The mcu needs to connect to a modem and a gnss module. Both modules will communicate with the mcu over UART
I'm...
I'm working on a prototype that has 8 BLE sensor nodes that are powered by coin cells and placed on different parts of a human body.
The host node is the main processing...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
I have one central and one peripheral device connected over BLE. The peripheral has a custom service characteristic containing the firmware Version value. After connecting...
On a custom board we are using an RTC chip to generate the 32khz clock.
I have verified that the hardware register is set to external, bypass, and the src is xtal. The clock...
