Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
I am writing a program that receives a command from a phone using the BLE UART example. The program can count up or down depending on the command. On every count, I...
Hi,
i'm developing an application that uses scan response.
AFAIK sd_ble_gap_tx_power_set is used to set the advertising tx power (BLE_GAP_TX_POWER_ROLE_ADV).
Is the...
Hello,
I am sunning trying to build the hello world sample as mentioned here:
For this project I am working on ubuntu(VM 22.04.1)
I have followed all the steps as mentioned...
-
Is it better as the ATT MTU size is larger?
I am trying to do nus communication between nrf board 1 and board 2. The data size I want to send is about 30 bytes. Previously...
To make sure that the nRF52840 SoC is not powered when the nRF power switch (SW8) is OFF.
So what happens if I power the nRF52840 SoC when the nRF switch (SW8) is ON ?
Hi ,
When i run samples/keys/hw_unique_key app and select nrf9160dk_nrf9160_ns board . The app can not run into main function instead run into system_halt.
__WEAK...
Please provide the part number(s) of low-cost NORDIC processors that have a quadrature decoder and a PWM.
We are working on an application that is using a Nordic nRF52840...
Hi,
During the validation of our device, we found that the RTC (synthesized from HFCLK) was quite a bit off. Instead of the expected 32.768kHz, we measured 33.047kHz.
...
Hi, I am using urf52832 ( also have 52833 dk).
I am trying to use another pin us uart, which tx is 29 rx is 30 define in project_pinconfig.h.
But I can't see any uart...
Hello, I'm working with BLE Mesh using NRF52840
- Our setup: NRF-Connect-SDK 2.1.0
- Summary of our project.
+ Provisioner node to control lightness for all nodes in...
Hi,
I'm having an issue including USB DFU Trigger library in my prototype application running on nRF52833.
My application is based on the ble_uart example, to which I...
Hi,
My application is written on top of freertos ble example. I need to integrate radio test example as well for certification. I am running into errors when I try to...
Hello,
my first Post here, so i hope i do it correctly.
I have the following Problem with the Configuration and Communication over TWI/I2C.
The Voltage of the TWI...
