My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Using the Power Profiler Kit II with
nRF Connect for Desktop (v 3.11.1) on Ubuntu 20.04 with the Power Profiler App v3.4.3
I'm wondering about the value of the time axis...
When operating in high-voltage mode, the spec says that VREGH,DROP is at most 0.3V . What happens if VDDH falls below the programmed VDD output plus VREGH,DROP, for both the...
Dear Community, Following the Nordic's sample of the (<ncs root>/nrf/sample/caf) the LED module & (CAF) Button module demonstrate the LED states & LED effects (awesome!) After...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example and faced some troubles.
I'm following this guide https://infocenter...
I want to use the BLE Secure connection feature with the following options
CONFIG_BT_SMP_SC_PAIR_ONLY=y
CONFIG_BT_SMP_SC_ONLY=y
CONFIG_BT_SMP_APP_PAIRING_ACCEPT=y
CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY...
Hi
I'm working with a PDM mic for nRF52832 SDK v17.1 on a project and I have a questions about PDM driver working.
Whats the difference between the buffer pointer in nrfx_pdm_buffer_set...
Hi Team
In thingy91---hardware-files-1_6_0.zip, the QM12038 is end of life status now. So do we have any new design to replaced it? Thank you.
www.qorvo.com/.../QM12038...
I just finished the second prototype of a nRF9160 board. First one worked flawlessly, but had poor GPS reception. Rewamped the matching and added SAW filters.
However, now...
I have to switch between several different scanning modes.
I scan in passive mode to get all sensors' advertisements (no connection).
I scan in active mode to get a specific...
Hi everyone
I want use the pwm_driver example of the SDK download at nRF52833 DK
However, some problems were encountered after the migration
I replace the preprocessor...
Hi,
I just started looking around with the NRF52840 development kit and tried to implement simple GPIO interrupt based on the button sample .
I settled multiple GPIO...
Hi All,
If I enable UART module or my code has any stdio functions retargeting to read/write, the debug mode does not work. I am getting the following error:
========...
Hi,
I develop firmware for nRF5340 in VS Code with Nordic toolchain (1.9.1) and NRF connect addon.
Project generates multiple elf files and it seems like only zephyr\zephyr...
Greetings to Nordic team!
I would like to provide BLE security for my application (to my BLE Peripheral device). I am planning to apply the following features such as...
Hi Nodic community,
Could you please help me to flash my Nordic Thingy:91 development board. I was able successfully build Zephyr-based project by following instructions...
