Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi.
I try to build the example Matter: light bulb and in the terminal shows an error that iI don´t underestand what is the problem.
Please ¿Any could explain me why ocurs...
Hi,
I am using the Thingy:91X device and can see the updates appearing on the hello.nrfcloud.com web application, but I would like to have access to the 'device' via the...
As the title said, I'm currently on the nRF21540 DK. I turned on Async UART:
CONFIG_UART_1_INTERRUPT_DRIVEN =n
CONFIG_UART_1_ASYNC =y
CONFIG_UART_1_NRF_HW_ASYNC =y...
Hey Nordic Team
Just looking for guidance and clarification on the nPM1300 setup. couple of questions on the sample setup below.
Project Overview
Project is a consumer...
I setup 2 Holyiot nRF54L DK Development Boards with the channel sounding sample code from NCS 3.1.1 samples/bluetooth/channel_sounding_ras_initiator (initiator and reflector...
Hi all,
I’m planning to add crypto support to my nRF52811 application. My main requirement is encrypting and decrypting a string , but I’m hitting flash size constraints...
Hi，
I am using the nrf52840DK development board and running the SDK of version ncs/v2.6.0. When I flash the samples/esb/esb_ptx and samples/esb/esb_prx projects onto the...
Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Hello,
I am new to embedded programming and I'm trying to create a small application that uses BT advertisements. I've tested my code on an NRF52840 dongle, and a board...
Hello,
we made a circuit board with nrf5340. We only burned the blinky program once for testing and it was successful. However, when we tried to burn the program again,...
Hello everyone,
During the design of my core board, I encountered an issue where after flashing a demo program, the core board cannot be programmed again. The demo program...
I want to pair my Oticon hearing aid with a Bluetooth LE audio/Auracast transceiver for streaming from laptop or mobile or TV to my hearing aid. It is a personal use case...
Hi there
I'm trying to make the SPI work on nRF53 (My board is nRF7002 DK) refer the tutorial academy.nordicsemi.com/.../ but I had the issue about frequency of spi peripheral...
I recently purchased the Maker Diary nRF9151 Connect Kit (LTE-M/NB-IoT, nRF9151 SiP) and I am using the iBasis SIM that came with the Nordic Thingy:91. The device is unable...
