Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I have two custom boards, one is central with nRF52933 and other is peripheral with nRF52832.
In the previous test, the connection between the 52833 central board...
Hi Team
Because Ble_2Mbit have better RX sensitivity than Nrf_2Mbit. Can I use Ble_2Mbit in ESB code? Is there any potential technical or legal risk? thank you.
regards...
Before updating to V2.00, the DTM tool can automatically detect the serial port, log has a clear indication whether it is connected to the target board, when the DTM update...
Hello.The SDK version I'm using is 17.0.1 and the protocol stack version is S140_7.2.0. I use the nrfutil to generate the update zip file for dfu,but I find that the nrfutil...
Hello! I have the whitelist support for my device with the default settings:
My goal is to rewrite saved addresses in the whitelist, when there is a new 9th address bonded...
Hi,
I'm working on adding the buttonless DFU function to my application. It works fine when I disable NRF_PWR_MGMT_CONFIG_AUTO_SHUTDOWN_RETRY in sdk_config.h . However,...
Hi everyone.
I have a custom board with nRF52832. I am using J-Link for programming. In my custom board, SWD pins are exposed. So I can erase nRF52832 succesfully and programmed...
I have recently switched from development with the nRF52832 to the nRF52840 and along with this switched from the nRF52-DK to the nRF52840-DK. I am unable to connect to the...
Hi everyone,
I try to connect simulatanoues 12 BLE devices to a Linux PC with Bluez.
You cannot go above 5 with commercial BLE controller.
So I want to use the dongle...
As many others have found, and answered questions here and here and in other posts, DFU will prematurely exit IF you have enabled WDT in your application, as the current Nordic...
Dear Nordic Engineers
I recently encountered a problem when developing NRF9160.I developed it based on the example of asset_tracker_v2.Now I have an .a file of an encryption...
I am using SDK 15.2 with Segger Studio
I am using an external button on pin 4 to enter sleep mode on a long press and wake up the device.
I am able to enter sleep...
Hi
I am using sht85 to detect temperature/humidity in my Light lightness server code
In the original server code, by pressing 1 or 2 you get to either decrease or increase...
Hi,
I'm working on a project using the nRF9160 (NCS V1.7.1, V1.3.0 modem firmware) and am utilizing the 1PPS signal.
It is working well, however when the fix is lost...
Is it possible to get access to an old version of the Bluetooth App in nRF Connect Desktop? There has recently an update that has proven very unreliable. It constantly crashes...
