Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I want to know if I call the following function, which condition should I meet to determine that the coordinator is not connected to any terminal devices. For example, I now...
Hello, I am looking for some help or example code that describes minimum set of the files and #defines required to enable AES 128bit encryption and decryption using ECB mode...
Hello,
I'm trying to learn what might be typical latencies for Bluetooth LE Audio. For instance, the aptX low latency codec claims latency around 20-40ms. Is Bluetooth LE...
Studying the documentation for the nRF52811, I found a difference in the description of memory recording and memory erasure:
write: " The CPU is halted while the NVMC is...
Hi,
I have nRF52840 DK and am using nRF5_SDK_17.0.2_d674dde.
I am not using SoftDevice, and Zephyr RTOS.
I have a simple program and using RTC0 timer. My code snippet...
Good afternoon,
I have a question regarding the nRF9160 and the eSIM configuration. We have developed a prototype PCB based on the nRF9160 DK and included an eSIM. However...
Hello,
I am trying the example of ble_app_uart and when i am building the example it gives me an error RX_PIN_NUMBER undeclared. When i load the pca10056.h i can see TX_PIN_NUMBER...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b and FreeRtos
This device has some bindings already set...
Hi,
my zigbee network for 120 sensors. if i declare 120 install codes then most of them don't work. The "zb_secur_ic_add" function works without error, "zb_secur_ic_get_list...
Hello!
Following problem:
I try to save 100Byte uint8_t messages in the nvs on the nrf9160.
Sometimes it works and only some moving logs come up and sometimes the following...
Hai
I have a requirement to download the FW application of NRF9160 M33 via serial UART. Is this possible?
So, which zephyr project am I to consider for reference?
...
Hi all,
looking for samples for using CoAP with DTLS 1.2 (PSK) on nRF9160. All the samples I can find are not using DTLS. Highly appreciate any hint!
Thank in advance...
After a painful sequence here
https://devzone.nordicsemi.com/f/nordic-q-a/80283/how-to-use-the-trigger-library-to-program-the-nrf52840-dongle
I managed to merge the projects...
Hi, We have firmware running on a 833 board, and we had noticed that connection times with a NodeJS central takes around 8-9 seconds. We thought that this had to do with the...
