Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am testing the nRF9160 DK and used the asset tracker application with the IBasis SIM. Application works fine under CAT M1 network (IBasis SIM is roaming on o2/Telefonica...
Hello
We want modify mcuboot_primary and mcuboot_secondary partition.
mcuboot_primary end_address change to 0x70000 and size change to 0x60000.
mcuboot_secondary end_address...
Hello,
I'm trying to use MQTT API to get the information about connected/disconnected devices.
I'm subscribed to the topic: xyz/a/connections and I'm able to receive connection...
Hello,
I am trying to use the HID Keyboard Demo (ble_HID_keyboard_template from arduino sdk) . I'm using a RedBearLabs Blend Arduino with the nrF8001.
It works great...
Hi ,
I have been working on an example code in SDK : nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\pca10040\s132\ses\ ...
Hi, On our new type of 9160 based boards, we failed to create a connection with TLS socket. After creating a TLS socket Without peer verification, and trying to connect with...
Hello,
Is it possible to use the nRF5 SDK v15.0.0 and nRF Connect SW to perform DFU upgrades? Are there any compatibility issues?
Is it advisable to continue using nRF5...
Hi,
I have purchased a ESIM from https://www.taisys.com/ , which works with DUAL Profile or Two networks.
We need to enable SIM TOOL KIT (STK) for enabling the sim...
Hi Guys,
I want to use nRF52840 Dongle as "BLE central UART".
In the first step, i used a nRF52840 Dongle with a Bluetooth low Enegy app in a nRFConnet, the result is...
Excuse me:
I can't find a api to close WDT，When the chip enters idle mode, the watchdog will reset the chip，I tried to call the command in the diagram below to turn off...
Hello,
I'm using nRF52832 board and I want to use it as a controller with a third party cellular modem to connect to AWS IoT. i.e. I want to send AT commands with the UART...
Hi,
I am trying to minimize the power consumption on a NRF52840.
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf52-designs states...
