Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I tried running the crypto sample example as part of the nRF SDK project on my nRF5340 DK.
I successfully completed as few tests and then fails while trying to run...
Hello Nordic Team I want to use the ble_app_beacon example found in SDK 15.3 on NRF52810 when NON_CONNECTABLE_ADV_INTERVAL is MSEC_TO_UNITS (5000, UNIT_0_625_MS). The program...
We are using the QDEC in an nRF52832 and our rotation speeds are 0 to 15rpm, usually around 10rpm. Is there any fundamental reason the QDEC can not be used in this case? We...
I'm trying to get the bmi160 sample to work with my custom nRF9160 board. I think the sample is quite old and not maintained. Unmodified (except fixing pure compilation errors...
Hi.
I am building an I2C driver for the Sensirion SPS30 particle sensor (datasheet: https://no.mouser.com/datasheet/2/682/Sensirion_PM_Sensors_SPS30_Datasheet-1888453...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
Hi all!
I'm trying to run the BLE light switch example on the nRF52833 development board using Segger. I get the following error whenever I try to build the client. This...
sorry where i can find the document/spec for the API that we can use to comunicate with LTE stack L3 . Using Zephyr ? threre are some examples that can help me ?
Best Regards...
Hello everybody, I have to develop an embedded system to acquire and process data. I will be using 2 custom PCBs based on nRF52832: 1- Sensor board: very low power consumption...
Hi Nordic, Please, I am doing a design with nRF52840 and would like to be clear on a few points. Attached is the electrical diagram .
Point 1 For the power supply I am using...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
Given a 3rd party BLE device (for example a fitness) watch, would it be possible to connect to it using the nRF52 DK and conduct a DFU on it? If so, is there any documentation...
Hi,
I am trying to nrfutil to execute dfu over BLE using nrf52 dk and nrfutil. I have no problems when I try to use nrf_connect mobile app, but I want to use nrfutil desktop...
I want to write my application logs to the flash. I am following this tutorial which is for nrf52: https://jimmywongiot.com/2020/02/24/print-log-flash-log-crash-log-on-nordic...
I want to change the GPIO settings for the pin P1.08 but in the register description (nRF52840_PS_v1.2.pdf) there are only the names and offsets for the pins from P0.00 to...
