Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I've been looking for a DC Motor controller example (for nRF52840) but without luck. Some other users have referred to such an example so I figured it should exist.
Anyone...
I am using SPIM4 with easyDMA in list mode to read a set of registers from an SPI device, and everything seemed to work great until I attempted to use the double buffered...
For some reason I can no longer compile any Zigbee examples.
The errors I am getting are below.
I have no idea what the issue is and I can't find any resources to help...
Dear sirs,
Here we've faced with the issue about logs output, could you please help?
We need to use two CDC_ACM devices on the board: one for shell and printk() output...
Hi!
I'm developing a peripheral device using nrf52840 to communicate with our android developed app. I'm testing the latency between connections of device. the configurations...
Hi, I need to estimate the power usage (so looking for TX and RX duty cycle) for the NRF52 during operation.
We will be connecting to a heart rate strap, and recording...
Hello - our certification lab is using the radio test example in order to perform their testing. They claim that the lowest channel they are able to set within the example...
Hello,
I am using nRF52833, nRF Connect SDK v1.5.0.
In v1.5.0 there is one new example i.e Zigbee NCP. ( Zigbee: NCP — nRF Connect SDK 1.5.0 documentation (nordicsemi...
I'm trying to update the advertising data using sd_ble_gap_adv_data_set function but it's not defined in sofdevice s140 v7.2.0 , it's defined in v5.0.0-3.
Please how can...
I installed NRF connect SDK v1.5.0-rc1.0 through toolchain manager.Open SES and create a project with open NRF connect SDK project.An error occurred.'create_nordic_project...
This function succeeds only when Thread protocols are disabled. my question is: if the Thread protocols are enable,what should I do to disable them ，now what I do is:
"otThreadSetEnabled...
Hi . I am developing nRF52 for the first time. (PCA10056_ nRF52840 _S140_ ver1.70.0 _DK under development..) It is under development with SEGGER embedded studio. I want to...
I'm new to NCS, and playing it with nrf5340 pdk kit.
My problem is ,I can't play any projects, all of them go to the same error: cmake failed,create_nordic_project.py failed...
Hi,
To support the large and dense networks we are building, I need my network coordinator to be able to throttle OTA packets to not completely overtake the network’s bandwidth...
