To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
I'm working with the nRF7002DK board using NCS version 2.6.0 . The internal flash is full, so I need to perform BLE DFU using external flash. Is there a sample available for...
Hi,nordic team
Iam programming with nrf52833 and ncs v2.9.0
I am doing DFU by myself.And I Flash_write data into slot1_partition,I am sure my data write in flash is correct...
How can this be done?
calls to bt_id_reset, and bt_id_delete do not work on the BT_ID_DEFAULT.
I wish for the device to appear as a different device (IRK) each time it...
Hi all,
Actually I'm building with vscode my firmware for a custom board build with an nRF9151 non secure. After building I got a merged.hex file, this is the file upload...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
Hi, our company is currently using nRF52832/RSSI feature to provide simple asset tracking/location service. Would like to know if we want to improve the accuracy by using...
Hi, we're creating a BLE mouse. We've setup the HID service- clicking button 1 on the nrf52832DK sends left mouse button click- nothing else is being sent. The problem: even...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Hello DevZone,
It seems that the nRF 52840 DK has 1MB of internal flash memory and it can be extended by external memory via QPSI. I have found External Memory source where...
Hello, I have an application that performs a DFU on my board. Is it possible to check at runtime which flash device is used for the secondary image? I know I can see it in...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
