Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I am using the modem callback:
To check if the modem is connected using the following code:
However, as far as I understood this only indicates that the modem...
Respected Sir, Mam
I am Noel Joe Riju Antony a student of Amity University, Noida, India pursuing a B.Tech in Aerospace engineering. I am currently working on a CW radar...
Hi,
I've got a Thingy:91, which I've spent a lot of hours in understanding the different samples. I want to be able to send GPS information to my Azure IoT hub device...
Utilizing SDK 15.2 and Softdevice S132, when debugging with Segger Ozone and starting from main or after triggering a reset to restart at main an ERROR 8 [NRF_ERROR_INVALID_STATE...
Tried running android app in debug mode, but I could not see any data on the crash.
tried resetting the board a few time and re commissioning.
followed the guide to set...
I found a lot of posts with this warning/error, but I could not find a fitting solution among them.
in my case, I copied the `peripheral_lbs` project to another folder,...
Hello
I have a few questions regarding the "ble_thread_dyn_mtd_coap_cli" example:
In the "main.c" file, I notice that you have created timers to call "sd_ble_gap_conn_param_update...
Hello.
I have a custom board with a uBlox BMD300 on it. The BMD300 is based on the nRF52382. The BMD300 had a pre package firmware in it that acted as a BLE UART bridge...
Hi all,
I am using the python bindings in recent weeks to development a BLE scanning device and have found the python bindings very useful for getting the kit up and running...
On MacOS Big Sur (11.2), trying to get started with nRF5340 samples, but getting create_nordic_project.py failed (1) errors.
I installed manually using the nRF Connect v3...
We are in the evaluation phase of a technology that is planning to use sound to transmit data between phones and devices.
We are currently using Quiet open source library...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
Hi,
I try to do the Onboarding workflow for 1NCE SIM Cards with the NRF91 Module: 1nce.com/.../
So the solution is to send a GET Request to a special endpoint and you...
We have certified the Centauri gateway with https://fccid.io/2AKNO-VOLCT200LTE ID. Now We have a query that we used nrf52840 chip as a BLE during certification.
Now on this...
Hi, nRF newbie here, forgive me if I'm being dim. I've searched the devzone, can't see obvious answers. nRF52840, SDK 17.0.2, Nordic SES 5.30a, using nrfx_* drivers I'm using...
