Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello, I'm testing an example of a zigby light bulb with a nrf52840 (pca 10056) board.
Here, when I press "BUTNERT 1" on ZED, I want to send the [ON/OFF] status of the current...
The average current during the nRF9160 test DRX is 2.2mA. The period of DRX is 2.56s. Using a China Mobile IoT card. I am testing on the DK board and have turned off all peripherals...
I used NRF24L01 to transmit the data without ACK mode. The receiver received the data normally when only the WR_TX_PLOAD_NACK instruction was used to send the data.If the...
Hello,
I want to set a GPIO Pin to high. Therefore I wrote the code below.
But when the software is written onto the nrf52811, I can not messure any voltage.
I do not...
Hi,
I am going to do data communication between two boards with libuarte. I see that both txdata and rxdata should be uint8_t*. But if I try to transmit the char*, will...
Hi On a nrf9160, I need to send data via UART(E) at 921600 baud. According to the UARTE BAUDRATE register documentation the register value 0xF000000 (Baud921600) leads to...
Hi,
I changed application main.c to enter in to DFU mode after 20 seconds. System is reset every 20 seconds and the boot messages are printed. The message "Booting (0x8200...
I am trying to measure distance with a vl53l1x sensor through the twi_sensor example. I uploaded the code to segger by referring to sparkfun, but twi_handler does not work...
Hi
using sdk17, softdevice132...
There are some parts of the central implementation that I don't understand.
It is based on cle_uart_app_c.
Isn't the function bl_nus_chars_received_outprint_print_called...
It is amazing how common this error is - there must be 100 posts. Yet none solve the problem and none explain it. It suggests that there is some serious work needed to improve...
I've been developing using nRF52840 using the nRF5 SDK. I have also been using FreeRTOS in my projects.
I recently received an nRF5340pdk to evaluate the nRF5340. I have...
Hi,
The CPU at my target board is nrf52840 and SDk16.
Condition 1: It causes system lock at <-A-> (function of strlen at nrf_ble_scan.c) if I setup the filter of NRF_BLE_SCAN_SHORT_NAME_FILTER...
I am looking to use the nRF9160 in eDRX intervals of 2.7 minutes (no PSM). The goal of the device is to be dormant until receiving a command to begin transmitting its location...
Hi,
I am developing an application based on Connectivity Bridge and I want to establish few simultaneous Bluetooth connections. I am working in Thingy:91, currently on SDK...
