Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I have gone through this ticket --> https://devzone.nordicsemi.com/f/nordic-q-a/30104/how-do-i-share-private-questions-with-my-coworkers-using-the-new-devzone
But...
Hi,
I am using NRF52840.
After upgrading to SDK 17, I found that the chuo stays in boot mode because this new condition (I highlighted it in the code below):
if (NRF_BL_DFU_ENTER_METHOD_GPREGRET...
Hi
I have some questions.
I'm trying to communicate with BLE using 9160DK with my smartphone.
1. Do you have a simple example? 2. Can I send videos or pictures using...
Hi nRF support team, By using the nRF Connect SDK, I am trying to create a timer, which I can use for incrementing a counter by 1 for each second on a timer interrupt handler...
Hi,
I am trying to merge the ble_app_becon with dfu. What are the things I need to add. In becon example I don't find the services_init() function. Do i want to include...
Hi,
I am using the latest SDK, with the nRF52840.
using the usbd_ble_uart example.
Created a timer that starts to send packets to the PC throw USB with a running index...
Hi Dev Team,
I have an iot.1nce.net sim that I am using in Germany.
+CGDCONT: 0,"IP","iot.1nce.net","10.205.84.3",0,0
I was trying the eDRX configuration using a basic...
Hi,
The ' nRF52840 Errata Attachment Anomaly 172 Addendum' linked to in the nRF52840 errata (Version 1.3, page 17) seems to be missing; the link gives a 404 error. Where...
I've tried to test the ZigBee OTA example on the 4.1.0 SDK, but it does not work. I've gone through the exact steps of the procedure as described in the infocenter, but it...
Hello,
in our project we have a nRF52840DK as central (s140) and a custom board with nRF52832 chip as peripheral (s132). The software on the nRF52840DK is based on the ble_app_uart_c...
When I program the Zigbee cli example from T&Z SDK v4.1.0 I see that the Zigbee stack uses some flash areas at the end of the chip. In my case 304 bytes @ 0x000F7000 and 24...
Hello,
Using libuarte I have been able to set up UARTE0 and UARTE1 for main communications, and debug communications respectively. While using UARTE1 to print out debug...
Hi,
I's trying to implement switch two application firmware in the openbootloader example, but I meet some issue.
I change the sector to 0x27000 in App1, 0x40000 in...
Hi, in my app, I have to implement sleep between transmission running at 4Hz. On the background there is running adc, which data are collected via ppi, timer and SPI easy...
When turning off the UART device, the UART ASYNC API callback will be called with the UART_RX_STOPPED event.
This will then not recover, and the event will be spammed infinitely...
