Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I'm trying to run the https_client sample on an nrf9160dk, and it's giving me the following output:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1-1440-g"020" !$#a 1...
Hello,
I have purchased this device to use as a BLE sniffer. I have followed this manual to configure the device as a sniffer:
https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3...
Hello.
I'm using a nrf52 dk (nrf52832) + GCC 9.2.1 (9 2019 q4 major) + WIN10 + CLION and I'm trying to build an example project using GCC.
I get the following error: ...
Hello everyone ,
I have question about saving the configuration of Friendship so-that after rebooting the SOC, the friendship's configuration restored without applying the...
Hi, I'm HongJae.
I'm developing a Bluetooth peripheral program with nrf52.
Briefly,
if I send a hexadecimal message(e.g 0x35), GPIO's are ON.
After 1 minute from...
hi,
I found a interesting thing：I use the output function to configure the P0.14（nrf_gpio_cfg_output(14)）. After configuration, the normal output should be low, but it outputs...
hello all,
i am using nRF52832 SoC in my project and my requirement is to write some configuration into internal flash when i flash the program using segger j link.
for...
Hello.
I am evaluating with nRF52833 DK board. I checked both peripheral/uart and ble_peripheral/ble_app_hrs.
Examples work each well on nRF52833 DK. I want to add the...
Hi support Team,
Following are my Questions.
1. Please recommend me three development boards from Nordic. I would like to build the mesh Network.For example one will transmit...
I am seeing a number of issues, but since they appear to be different, I will use different threads.
Setup: have gone to ble_blinky example to keep things as simple as possible...
Hi, i am new to the nRF52840, i like the features it has and i want to create a board using it. In the datasheet it is said to have 2 ARM processors and i want to use it as...
About 3.7V Li-Po battery on spec., can we read adc value from the battery using p0.04(A1) without external voltage divider circuits? In fact, 3.7V battery outputs 4V ,seeing...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
How can I define paths in SES (Windows), like $SDK_PATH, for my project?
- if they are defined in macros, what is the syntax?
- is there a standard variable that has a...
