We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I have an nRF91 DK v0.7.0 which I'm using for the first time with a Hologram.io SIM card and nothing seems to be working. Nordic sales and an FAE were here in late February...
Hello,
I need to get nrf9160 to connect to a LTE-M network. We are using a custom pcb module with nrf91 on it. I've managed to get a simple hello world, blinky and gps simulator...
Hi,
I am currently working on a project in Mesh on nRF52840 DK.
I am using the mesh v3.1.0.
I wanted to send command from mobile app to particular node in the mesh and...
Hi, i use the saadc example(triggered by ppi+timer) with uart to get voltage signal and transmit to central device( another custom nrf52832 board), and the central prints...
I am using SPI communication to transfer data from an ADC (ADS1220) to my nrf52382, then to the mobile app via bluetooth. The ADC is the slave. The NRF is the master. So MISO...
Hi,
I am trying to read data via an ADC through SPI and send it via Bluetooth to the NRF mobile app. I checked that both the original BLE_UART example and the SPI master...
My SPI data transfer from a peripheral ADC works fine in the SPI example project. The same code doesn't transfer data properly when it is added in either a ble_template or...
Does the BLE NUS service use pins on the NRF? I'm using a custom made nrf52382 pcb where I transfer data from an ADC (ADS1220) via bluetooth to the nrf Toolbox app. But using...
static const nrf_drv_twi_t m_twi = NRF_DRV_TWI_INSTANCE(TWI_INSTANCE_ID);
Hi Everyone,
I'm new to nRF52832 programming. I want to learn more about nRF52 programs.
...
In SDK 15.2 is the nrf_cli module completely thread safe? I was thinking of developing a wrapper to use the CLI module for both application logging as well as a general CLI...
Hello,
i am using the PWM peripheral in the waveform mode to generate a complementary signals for a piezo beeper connected between two GPIOs.
I use the sequences to play...
I'm upgrading my code to SDK 15.2. I use TIMER1 and PPI to trigger SAADC sampling. The same to what I was doing on SDK 12.3. I was doing 100Hz sampling, but was hoping to...
I have two SPI ports, each connected to multiple SPI devices. Can I apply for two m_nrf_spi_mngr at the same time? (NRF_SPI_MNGR_DEF(m_nrf_spi_mngr, SPI1_QUEUE_LENGTH, SPI1_INSTANCE_ID...
Hi,
We are using nrf52832 with softdevice 6.0.0 ,SDK 15.0. Our code is based on the FreeRTOS heart rate example.
We have one button in our system and when we press it...
I am working on the Mbed-OS HAL implementation for the nRF52840 USB device.
I have it almost passing all the automated tests. One where it fails is when the Mbed test suite...
