Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I want to enable Notifications in my Central for a particular characteristic advertised by my Peripheral. There's example code that is supposed to do this in the BLE Central...
Hello,
i have a question about the use of the dc/dc converter in use with the softdevice S310 v3.0.
We make some difficult calculations and so the sensor its on for 750ms...
hi
as we know,ANCS need to pair,we have app for ios,iphone will pair with our devcie when i connect my device by my app,so iphone will connect my device when user open...
hi
my customer want to add DFU funcation to their APP(ios and android),i give them nrf toolbox source code ,i hope they can separate DFU funcation from that source code...
In my application I have to advertise and scan, I know these two actions are multiplexed and there are no problems when there is no BLE connection (I use s130, sdk 9.0.0)...
Hi all,
I'm developing little project on nrf51 dongle(pca10031). After few succeses now I have big failure which stops my work.
How my environment looks like: Ubuntu...
I built the GCC bootloader from source based on the suggestion of another user in this forum instead of using a precompiled hex file. The Softdevice is 7.1.
It shows DfuTarg...
I have a min connection interval of 200ms and max of 250ms. I have set slave latency to 10. These parameters are set both on peripheral and on central. Still, after connecting...
Hi! I am working on a project that uses the Multilink example. On the client (nRF51422 w. SD 120) my program crashes and starts the main loop again after a few seconds. I...
Hi,
I'm developing a device that will be powered by two AAA alkaline batteries.
Since the operating voltage of nRF51822 is 1.8 to 3.6V I was considering to connect them...
Hi,
the example ble_app_uart_s132 from the SDK 0.9.2 is not longer working with the new release of S132 ( s132_nrf52_2.0.0-7.alpha). I had to go back to s132_nrf52_1.0...
My setups are:
RBL BLE Nano
nRF51_SDK_9.0.0_2e23562
Keil uVision V4.74.0.22 or gcc-arm-none-eabi-4_8-2014q2-20140609-win32
My design is to advertise a manufacturer...
I'm using nRF51422 with SDK 9.0.0 and S310 ver 3.0.0.
First, I program softdevice and dual bank bootloader by nRFgoStudio. After that it is possible to program my application...
Hi all,
first of all thank you for such a great knowledge base and community exchange.
I am pretty new in the development for nrf51822 devices.
I managed to run the...
The comment above app_button_init says, in part:
* @note Normally initialization should be done using the APP_BUTTON_INIT() macro
This macro is also mentioned in the...
